Hi,
I get this error on booting up 2.6.20 (Similar error on 2.6.17.7 also,
the message is slightly different in 2.6.17.7)
PCI Cannot allocate resource region 2 of device 0000:02:0a.0
PCI Error while updating region 000:02:0a.0/5 (f3e00004 != 0200)
PCI Error while updating region 000:02:0a.0/5 (high 00000000 != 4e351)
lspci shows me a bit weird status BIST is running (on 2.6.17.7)
on 2.6.20, the line which says BIST is running, does not exist.
I have attached the lspci outputs on both 2.6.17.7 and 2.6.20
The device is a PCI 2.2 compliant device a multimedia bridge device
called Mantis.
The card is a plain 32 bit PCI card in a 32 bit PCI slot on an Asus
P4C800 motherboard.
looking at lspci output, the last 3 PCI devices are using the same chip.
The last 2 devices are Rev 1 chips, whereas the one which is acting a
bit strange is a newer version from the same vendor.
Any ideas as to why it could not allocate the region ?
Thanks,
Manu
00:00.0 0600: 8086:2578 (rev 02)
Subsystem: 1043:80f6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 0604: 8086:2579 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: f1d00000-f3dfffff
Prefetchable memory behind bridge: d9b00000-e9afffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1d.0 0c03: 8086:24d2 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef00 [size=32]
00:1d.1 0c03: 8086:24d4 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 23
Region 4: I/O ports at ef20 [size=32]
00:1d.2 0c03: 8086:24d7 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 17
Region 4: I/O ports at ef40 [size=32]
00:1d.3 0c03: 8086:24de (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef80 [size=32]
00:1d.7 0c03: 8086:24dd (rev 02) (prog-if 20)
Subsystem: 1043:80a6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 22
Region 0: Memory at f7fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 0604: 8086:244e (rev c2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f3e00000-f7efffff
Prefetchable memory behind bridge: e9b00000-e9bfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:1f.0 0601: 8086:24d0 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 0101: 8086:24db (rev 02) (prog-if 8a)
Subsystem: 1043:80a6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
00:1f.2 0101: 8086:24d1 (rev 02) (prog-if 8f)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at efe0 [size=8]
Region 1: I/O ports at efac [size=4]
Region 2: I/O ports at efa0 [size=8]
Region 3: I/O ports at efa8 [size=4]
Region 4: I/O ports at ef60 [size=16]
00:1f.3 0c05: 8086:24d3 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 0400 [size=32]
00:1f.5 0401: 8086:24d5 (rev 02)
Subsystem: 1043:80f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ee80 [size=64]
Region 2: Memory at f7fff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at f7fff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 0300: 10de:0181 (rev c1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at f3de0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
02:03.0 0c00: 1106:3044 (rev 80) (prog-if 10)
Subsystem: 1043:808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size 04
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f7eff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at dc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:04.0 0104: 105a:3373 (rev 02)
Subsystem: 1043:80f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 90
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at df00 [size=64]
Region 1: I/O ports at dfa0 [size=16]
Region 2: I/O ports at d880 [size=128]
Region 3: Memory at f7efe000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at f7ec0000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:05.0 0200: 10b7:1700 (rev 12)
Subsystem: 1043:80eb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size 04
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f7ef8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d400 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
02:0a.0 4e35: 1800:4e35 (rev 08) (prog-if 18)
Subsystem: 002c:c200
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR+ <PERR+
Latency: 0, Cache Line Size 0c
BIST is running
Region 0: Memory at f7ee0000 (32-bit, non-prefetchable) [disabled]
[size=4K]
Region 2: Memory at e9b00000 (32-bit, prefetchable) [disabled] [size=4K]
Region 3: Memory at <unassigned> (32-bit, prefetchable) [disabled]
Region 4: Memory at <ignored> (32-bit, non-prefetchable) [disabled]
Region 5: Memory at <invalid-64bit-slot> (64-bit, non-prefetchable)
[disabled]
Expansion ROM at e9b01000 [disabled] [size=4K]
02:0c.0 0480: 1822:4e35 (rev 01)
Subsystem: 1822:0014
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e9bfe000 (32-bit, prefetchable) [size=4K]
02:0d.0 0480: 1822:4e35 (rev 01)
Subsystem: 1822:0024
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at e9bfd000 (32-bit, prefetchable) [size=4K]
00:00.0 0600: 8086:2578 (rev 02)
Subsystem: 1043:80f6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 0604: 8086:2579 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: f1d00000-f3dfffff
Prefetchable memory behind bridge: d9b00000-e9afffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1d.0 0c03: 8086:24d2 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef00 [size=32]
00:1d.1 0c03: 8086:24d4 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at ef20 [size=32]
00:1d.2 0c03: 8086:24d7 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 17
Region 4: I/O ports at ef40 [size=32]
00:1d.3 0c03: 8086:24de (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef80 [size=32]
00:1d.7 0c03: 8086:24dd (rev 02) (prog-if 20)
Subsystem: 1043:80a6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 18
Region 0: Memory at f7fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 0604: 8086:244e (rev c2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f3e00000-f7efffff
Prefetchable memory behind bridge: e9b00000-e9bfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:1f.0 0601: 8086:24d0 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 0101: 8086:24db (rev 02) (prog-if 8a)
Subsystem: 1043:80a6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
00:1f.2 0101: 8086:24d1 (rev 02) (prog-if 8f)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at efe0 [size=8]
Region 1: I/O ports at efac [size=4]
Region 2: I/O ports at efa0 [size=8]
Region 3: I/O ports at efa8 [size=4]
Region 4: I/O ports at ef60 [size=16]
00:1f.3 0c05: 8086:24d3 (rev 02)
Subsystem: 1043:80a6
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 0400 [size=32]
00:1f.5 0401: 8086:24d5 (rev 02)
Subsystem: 1043:80f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ee80 [size=64]
Region 2: Memory at f7fff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at f7fff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 0300: 10de:0181 (rev c1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at f3de0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
02:03.0 0c00: 1106:3044 (rev 80) (prog-if 10)
Subsystem: 1043:808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size 04
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f7eff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at dc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:04.0 0104: 105a:3373 (rev 02)
Subsystem: 1043:80f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 90
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at df00 [size=64]
Region 1: I/O ports at dfa0 [size=16]
Region 2: I/O ports at d880 [size=128]
Region 3: Memory at f7efe000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at f7ec0000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:05.0 0200: 10b7:1700 (rev 12)
Subsystem: 1043:80eb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size 04
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f7ef8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at d400 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
02:0a.0 4e35: 1800:4e35 (rev 08) (prog-if 18)
Subsystem: 002c:4200
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR+ <PERR-
Latency: 0, Cache Line Size 0c
Region 0: Memory at f7ee0000 (32-bit, non-prefetchable) [disabled]
[size=4K]
Region 2: Memory at e9b00000 (32-bit, prefetchable) [disabled] [size=4K]
Region 3: Memory at <unassigned> (32-bit, prefetchable) [disabled]
Region 4: Memory at <ignored> (32-bit, non-prefetchable) [disabled]
Region 5: Memory at <invalid-64bit-slot> (64-bit, non-prefetchable)
[disabled] [size=32]
Expansion ROM at e9b01000 [disabled] [size=4K]
02:0c.0 0480: 1822:4e35 (rev 01)
Subsystem: 1822:0014
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e9bfe000 (32-bit, prefetchable) [size=4K]
02:0d.0 0480: 1822:4e35 (rev 01)
Subsystem: 1822:0024
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e9bfd000 (32-bit, prefetchable) [size=4K]
