Am Freitag, 22. Dezember 2006 14:10 schrieben Sie:
> Your mailer has mangled tabs into whitespace. Also, your patch needs to
> be applicable with -p1 from the root kernel dir.
I think, it was more the copy and paste from the shell; should have included
the file instead.
> Given the description of the problem it is probably more worthwhile to
> provide logs with USB debugging enabled, and usbmon logs, so that the
> real problem can be found.
I´ll gladly do that best I can, but might need some help what to do. In the
following is what I found so far.
Two straces of the usb backend. First one that worked ok (some seconds after
pluuging the printer in):
[...]
rt_sigaction(SIGPIPE, {SIG_IGN}, NULL, 8) = 0
open("/dev/usblp0", O_RDWR|O_EXCL|O_LARGEFILE) = -1 ENOENT (No such file or
directory)
open("/dev/usb/lp0", O_RDWR|O_EXCL|O_LARGEFILE) = 3
ioctl(0x3, 0x84005001, 0xbfd67cd1) = 0
fstat64(1, {st_mode=S_IFCHR|0600, st_rdev=makedev(136, 2), ...}) = 0
mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) =
0xb7fd4000
write(1, "direct usb://Kyocera/FS-820 \"Kyo"..., 161direct
usb://Kyocera/FS-820 "Kyocera FS-820" "Kyocera FS-820 USB
#1"
"ID:FS-820;MFG:Kyocera;CMD:PCLXL,PCL5E,PJL;MDL:FS-820;CLS:PRINTER;DES:Kyocera
Mita FS-820;"
) = 161
close(3) = 0
open("/dev/usblp1", O_RDWR|O_EXCL|O_LARGEFILE) = -1 ENOENT (No such file or
directory)
[...]
the ususal case (does not work):
[...]
rt_sigaction(SIGPIPE, {SIG_IGN}, NULL, 8) = 0
open("/dev/usblp0", O_RDWR|O_EXCL|O_LARGEFILE) = -1 ENOENT (No such file or
directory)
open("/dev/usb/lp0", O_RDWR|O_EXCL|O_LARGEFILE) = 3
ioctl(0x3, 0x84005001, 0xbfc397b1) = -1 (errno 5)
close(3) = 0
open("/dev/usblp1", O_RDWR|O_EXCL|O_LARGEFILE) = -1 ENOENT (No such file or
directory)
[...]
Here a piece of the kernel messages with CONFIG_USB_DEBUG=y (started the usb
backend two times, reading printer ID does not work):
[...]
Dec 21 18:48:17 heinrich usb 3-5.4: usb timed out on ep0in len=0/1023
Dec 21 18:48:37 heinrich usb 3-5.4: usb timed out on ep0in len=0/1023
[...]
yes, that´s all with CONFIG_USB_DEBUG.
Then, there are syslog messages with "#define DEBUG" in usblp.c:
After plugging in the printer:
[...]
Dec 21 19:56:12 heinrich usb 1-5.4: new full speed USB device using ehci_hcd
and address 6
Dec 21 19:56:12 heinrich usb 1-5.4: configuration #1 chosen from 1 choice
Dec 21 19:56:12 heinrich drivers/usb/class/usblp.c: usblp0 set protocol 2
Dec 21 19:56:12 heinrich drivers/usb/class/usblp.c: usblp_control_msg: rq:
0x00 dir: 1 recip: 1 value: 0 idx:
0 len: 0x3ff result: 91
Dec 21 19:56:12 heinrich drivers/usb/class/usblp.c: usblp0 Device ID string
[len=91]="ID:FS-820;MFG:Kyocera;C
MD:PCLXL,PCL5E,PJL;MDL:FS-820;CLS:PRINTER;DES:Kyocera Mita FS-820;"
Dec 21 19:56:12 heinrich drivers/usb/class/usblp.c: usblp_control_msg: rq:
0x01 dir: 1 recip: 1 value: 0 idx:
0 len: 0x1 result: 1
Dec 21 19:56:12 heinrich drivers/usb/class/usblp.c: usblp0: USB Bidirectional
printer dev 6 if 0 alt 0 proto
2 vid 0x0482 pid 0x0010
Dec 21 19:56:15 heinrich drivers/usb/class/usblp.c: usblp_ioctl:
cmd=0x84005001 (P nr=1 len=1024 dir=2)
Dec 21 19:56:15 heinrich drivers/usb/class/usblp.c: usblp_control_msg: rq:
0x00 dir: 1 recip: 1 value: 0 idx:
0 len: 0x3ff result: 91
Dec 21 19:56:15 heinrich drivers/usb/class/usblp.c: usblp0 Device ID string
[len=91]="ID:FS-820;MFG:Kyocera;C
MD:PCLXL,PCL5E,PJL;MDL:FS-820;CLS:PRINTER;DES:Kyocera Mita FS-820;"
[So far, so good. I then call the usb backend to read the printer ID]:
Dec 21 19:56:18 heinrich drivers/usb/class/usblp.c: usblp_ioctl:
cmd=0x84005001 (P nr=1 len=1024 dir=2)
Dec 21 19:56:23 heinrich drivers/usb/class/usblp.c: usblp_control_msg: rq:
0x00 dir: 1 recip: 1 value: 0 idx:
0 len: 0x3ff result: -110
Dec 21 19:56:23 heinrich drivers/usb/class/usblp.c: usblp0: error = -110
reading IEEE-1284 Device ID string
[...]
This is what I know until know. What can I do next? Learning about usbmon?
Thanks for hints.
Martin
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
