The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Signed-off-by: Nicolas Ferre <nicolas.fe...@atmel.com>
---
arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 3f750f6170f2..82d0c19e9720 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -880,6 +880,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(35))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(36))>;
+ dma-names = "tx", "rx";
clocks = <&uart0_clk>;
clock-names = "usart";
status = "disabled";
@@ -889,6 +896,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(37))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(38))>;
+ dma-names = "tx", "rx";
clocks = <&uart1_clk>;
clock-names = "usart";
status = "disabled";
@@ -898,6 +912,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(39))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(40))>;
+ dma-names = "tx", "rx";
clocks = <&uart2_clk>;
clock-names = "usart";
status = "disabled";
@@ -1016,6 +1037,13 @@
compatible = "atmel,at91sam9260-usart";
reg = <0xfc008000 0x100>;
interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(41))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(42))>;
+ dma-names = "tx", "rx";
clocks = <&uart3_clk>;
clock-names = "usart";
status = "disabled";
@@ -1024,6 +1052,13 @@
uart4: serial@fc00c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc00c000 0x100>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(43))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(44))>;
+ dma-names = "tx", "rx";
interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&uart4_clk>;
clock-names = "usart";
--
2.1.3
