Hi, On Fri, Jan 30, 2009 at 02:51:28AM -0800, peteridah wrote: > > Hello Dejan, > > I pressed the server power button until it goes off.....I realize that I > cannot pull the plugs with the stonith devices I am using.
OK. Just to make sure ... Thanks, Dejan > Thanks. > Peter Idah > > Dejan Muhamedagic wrote: > > > > > > > > How exactly do you "switch off" the node? > > > > Given your stonith device, you have to make sure that your nodes > > always have power. > > > > Thanks, > > > > Dejan > > > >> > I used crm_verify -L -V to check the config and I have no errors. > >> > However an attempt to simulate a failure returns with a warning in the > >> > logs > >> > - > >> > > >> > WARN: native_color: Resource Fs cannot run anywhere > >> > pengine[5868]: 2009/01/27_12:17:06 WARN: native_color: Resource JVIP > >> > cannot > >> > run anywhere > >> > >> When you shutdown 001, the resources have nowhere left to run due to > >> your configuration: > >> > >> <rsc_location id="cli-standby-ISGROUP" rsc="ISGROUP"> > >> <rule id="prefered_cli-standby-ISGROUP" score="-INFINITY"> > >> <expression attribute="#uname" id="6200ffd0-126c-4fa5-993f-a24627ce15a8" > >> operation="eq" value="cll-jcaps-002"/> > >> </rule> > >> </rsc_location> > >> > >> This forbids ISGROUP to run on 002. And that's the only node left. > >> > >> Judging by the id "cli-standby-ISGROUP", you propably used crm_resource > >> -M or the gui before to migrate ISGROUP. Both will have told you that > >> they were going to create this constraint and that - if you ever wanted > >> the resource on that particular node ever again - you'd have to revert > >> the migration by crm_resource -U or some function in the gui (not > >> familiar with that). > >> > >> So do that and ISGROUP should start on 002. > >> > >> Regards > >> Dominik > >> _______________________________________________ > >> Linux-HA mailing list > >> [email protected] > >> http://lists.linux-ha.org/mailman/listinfo/linux-ha > >> See also: http://linux-ha.org/ReportingProblems > >> > >> > >> > >> -- > >> View this message in context: > >> http://www.nabble.com/Linux-HA-configuration-on-SLES-10.2-problem-tp21725780p21728148.html > >> Sent from the Linux-HA mailing list archive at Nabble.com. > >> > >> _______________________________________________ > >> Linux-HA mailing list > >> [email protected] > >> http://lists.linux-ha.org/mailman/listinfo/linux-ha > >> See also: http://linux-ha.org/ReportingProblems > > _______________________________________________ > > Linux-HA mailing list > > [email protected] > > http://lists.linux-ha.org/mailman/listinfo/linux-ha > > See also: http://linux-ha.org/ReportingProblems > > > > > > -- > View this message in context: > http://www.nabble.com/Linux-HA-configuration-on-SLES-10.2-problem-tp21725780p21745035.html > Sent from the Linux-HA mailing list archive at Nabble.com. > > _______________________________________________ > Linux-HA mailing list > [email protected] > http://lists.linux-ha.org/mailman/listinfo/linux-ha > See also: http://linux-ha.org/ReportingProblems _______________________________________________ Linux-HA mailing list [email protected] http://lists.linux-ha.org/mailman/listinfo/linux-ha See also: http://linux-ha.org/ReportingProblems
