Uhm... that's strange, I don't have any of this cards to test, but other people reported that this solution was working. Could you post the dib0700_devices.c you're using to have a look?
Albert 2008/2/18, Antti Palosaari <[EMAIL PROTECTED]>: > > moi > It does not work for me. It says same PID-filter timeout as I have got > earlier. I don't have amplified antenna now, but I can say that all > other DVB-T sticks I have are working with this small antenna. It could > be that sensitivity of this hardware is bad or there is something wrong > with driver or firmware. Lets try to test it Windows to see if it is > working or not. > Logs attached. > > > regards > Antti > > Albert Comerma wrote: > > > Hey people, we already solved this problems. I submitted a patch a few > > days ago, but I think it's not on the current sources. I send again the > > patch. Basically it must use the same frontend description as asus > cards. > > > > Albert > > > > > 2008/2/18, Antti Palosaari <[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>>: > > > > > moikka > > I have also this device (express card). I haven't looked inside yet, > but > > I think there is DibCOM STK7700D (in my understanding dual demod > chip) > > and only *one* MT2266 tuner. I tried various GPIO settings but no > > luck yet. > > GPIO6 is for MT2266. > > GPIO9 and GPIO10 are for frontend. > > > > Looks like tuner goes to correct frequency because I got always > > PID-filter timeouts when tuning to correct freq. I will now try to > take > > some usb-sniffs to see configuration used. Any help is welcome. > > > > regards > > Antti > > > > Albert Comerma wrote: > > > Hi!, with Michel ([EMAIL PROTECTED] > > > <mailto:[EMAIL PROTECTED]> <mailto:[EMAIL PROTECTED] > > > <mailto:[EMAIL PROTECTED]>>) who > > > > > is a owner of this Yuan card we added the device to > > dib0700_devices, and > > > we got it recognized without problems. The only problem is that > no > > > channel is detected on scan on kaffeine or other software... I > > post some > > > dmesg. We don't know where it may be the problem... or how to > > detect it... > > > > > > usb 4-2: new high speed USB device using ehci_hcd and address 6 > > > usb 4-2: new device found, idVendor=1164, idProduct=1edc > > > usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3 > > > usb 4-2: Product: STK7700D > > > usb 4-2: Manufacturer: YUANRD > > > usb 4-2: SerialNumber: 0000000001 > > > usb 4-2: configuration #1 chosen from 1 choice > > > dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a > > firmware > > > dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw' > > > dib0700: firmware started successfully. > > > dvb-usb: found a 'Yuan EC372S' in warm state. > > > dvb-usb: will pass the complete MPEG2 transport stream to the > > software > > > demuxer. > > > DVB: registering new adapter (Yuan EC372S) > > > dvb-usb: no frontend was attached by 'Yuan EC372S' > > > dvb-usb: will pass the complete MPEG2 transport stream to the > > software > > > demuxer. > > > DVB: registering new adapter (Yuan EC372S) > > > DVB: registering frontend 1 (DiBcom 7000PC)... > > > MT2266: successfully identified > > > input: IR-receiver inside an USB DVB receiver as > /class/input/input10 > > > dvb-usb: schedule remote query interval to 150 msecs. > > > dvb-usb: Yuan EC372S successfully initialized and connected. > > > > > > > > > > > > > > ------------------------------------------------------------------------ > > > > > > _______________________________________________ > > > linux-dvb mailing list > > > > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org> > > > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > > > > > > -- > > http://palosaari.fi/ > > > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > linux-dvb mailing list > > linux-dvb@linuxtv.org > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > -- > http://palosaari.fi/ > > > Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > idVendor 0x1164 YUAN High-Tech Development Co., Ltd > idProduct 0x1edc > bcdDevice 1.00 > iManufacturer 1 YUANRD > iProduct 2 STK7700D > iSerial 3 0000000001 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 46 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xa0 > Remote Wakeup > MaxPower 500mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 4 > bInterfaceClass 255 Vendor Specific Class > bInterfaceSubClass 0 > bInterfaceProtocol 0 > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 1 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 1 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 1 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0200 1x 512 bytes > bInterval 1 > Device Qualifier (for other device speed): > bLength 10 > bDescriptorType 6 > bcdUSB 2.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > bNumConfigurations 1 > > Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5 > Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device using > ehci_hcd and address 6 > Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen from 1 > choice > Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6 > different device-types > Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in cold > state, will try to load a firmware > Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from file > 'dvb-usb-dib0700-1.10.fw' > Feb 18 23:50:55 localhost kernel: dib0700: firmware started successfully. > Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in warm > state. > Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete MPEG2 > transport stream to the software demuxer. > Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan > EC372S) > Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0 (DiBcom > 7000PC)... > Feb 18 23:50:56 localhost kernel: MT2266: successfully identified > Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully > initialized and connected. > Feb 18 23:50:56 localhost kernel: usbcore: registered new interface driver > dvb_usb_dib0700 > > [EMAIL PROTECTED] linuxtv]$ scandvb fi-Oulu > scanning fi-Oulu > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > initial transponder 634000000 0 2 9 3 1 2 0 > initial transponder 714000000 0 2 9 3 1 2 0 > initial transponder 738000000 0 2 9 3 1 2 0 > initial transponder 602000000 0 2 9 3 1 2 0 > >>> tune to: > 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > WARNING: filter timeout pid 0x0011 > WARNING: filter timeout pid 0x0000 > WARNING: filter timeout pid 0x0010 > >>> tune to: > 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > WARNING: filter timeout pid 0x0011 > WARNING: filter timeout pid 0x0000 > WARNING: filter timeout pid 0x0010 > >>> tune to: > 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > WARNING: filter timeout pid 0x0011 > WARNING: filter timeout pid 0x0000 > WARNING: filter timeout pid 0x0010 > >>> tune to: > 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE > WARNING: filter timeout pid 0x0011 > WARNING: filter timeout pid 0x0000 > WARNING: filter timeout pid 0x0010 > dumping lists (0 services) > Done. > [EMAIL PROTECTED] linuxtv]$ > > >
_______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
