Op zondag 11-02-2007 om 10:14 uur [tijdzone +0100], schreef Kristof
Pelckmans:
> Yesterday I went to a shop and was able to see that my Alphacrypt is
> working well. I think my Technotrend card is not seeing the CAM. Do I
> have to add extra load parameters to the module or load extra modules ?
>
> ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------
> lsmod
> Module Size Used by
> af_packet 13064 2
> snd_pcm_oss 36640 0
> snd_mixer_oss 14464 1 snd_pcm_oss
> rtc 10548 0
> parport_pc 23588 1
> lp 9604 0
> parport 33736 2 parport_pc,lp
> stv0297 6784 1
> ide_cd 34720 0
> cdrom 34720 1 ide_cd
> tuner 60200 0
> snd_hda_intel 15896 5
> snd_hda_codec 158720 1 snd_hda_intel
> dvb_ttpci 96868 16
> snd_pcm 61700 4 snd_pcm_oss,snd_hda_intel,snd_hda_codec
> saa7134 114528 0
> snd_timer 18692 2 snd_pcm
> snd 43748 14
> snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
> compat_ioctl32 1280 1 saa7134
> soundcore 6624 1 snd
> dvb_core 70568 1 dvb_ttpci
> ir_kbd_i2c 6928 1 saa7134
> i2c_viapro 7956 0
> saa7146_vv 44288 1 dvb_ttpci
> snd_page_alloc 7944 2 snd_hda_intel,snd_pcm
> video_buf 20228 2 saa7134,saa7146_vv
> saa7146 15112 2 dvb_ttpci,saa7146_vv
> ttpci_eeprom 2304 1 dvb_ttpci
> ir_common 29828 2 saa7134,ir_kbd_i2c
> via_agp 8320 1
> videodev 26112 2 saa7134,saa7146_vv
> v4l2_common 22144 4 tuner,saa7134,saa7146_vv,videodev
> i2c_core 17792 7
> stv0297,tuner,dvb_ttpci,saa7134,ir_kbd_i2c,i2c_viapro,ttpci_eeprom
> agpgart 26444 1 via_agp
> v4l1_compat 14724 3 saa7134,saa7146_vv,videodev
> evdev 8320 1
> <snip>
> 00:0b.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
> Subsystem: Technotrend Systemtechnik GmbH Octal/Technotrend
> DVB-C for iTV
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (3750ns min, 9500ns max)
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at febff400 (32-bit, non-prefetchable) [size=512]
> <snip>
> VDR does not mention my CAM :
I don't see a module budget-av loaded?
If you do a modprobe budget-av and check your "dmesg" log and perhaps
you see a:
"dvb_ca adaptor 0: PC card did not respond :("
If you see that message try to eject and reinsert the cam module after a
few seconds, perhaps you see a
"dvb_ca adapter 0: DVB CAM detected and initialised successfully"
afterwards in your dmesg.
- Jeroen
_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
