Hello,
I have searched all over the place and didn't find anything, so I figured this
would be the place to go.
I have recently purchased a DViCo FusionHDTV5 Express card and placed it into a
gentoo linux box. The current kernel drivers do not
appear to support it. I am not sure if it is trivial to add support or not.
If so, then I hope that the following information is
helpful in getting there.
==============================
Hardware:
Asus A8N-VM CSM
AMD Athlon 64 x2 4400+
1GB RAM
FusionHDTV5:
Chipset: CX23885
Tuner: LG H062F NIM
Technisat AirStar HD-5000AV
==============================
Software:
Gentoo linux
2.6.19-gentoo-r2 (gentoo-sources)
==============================
$> dmesg
...
Linux video capture interface: v2.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture cx2388x v4l2
driver version 0.0.6 loaded Losing some ticks... checking
if CPU frequency changed.
cx2388x alsa driver version 0.0.6 loaded cx2388x blackbird driver version 0.0.6
loaded cx2388x dvb driver version 0.0.6 loaded
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded
successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [LNKB] -> GSI 18 (level, low) ->
IRQ 18
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800007ccbe1]
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:0e:6c:aa
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Unknown/Unsupported NXT chip: 00 00 00 00 00
b2c2-flexcop: found the lgdt3303 at i2c address: 0x59
DVB: registering frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation (HD5000)'
at the 'PCI' bus controlled by a 'FlexCopIIb'
complete
bt878: AUDIO driver version 0.0.0 loaded ...
==============================
$> lspci -v
...
02:00.0 Multimedia video controller: Conexant Unknown device 8852 (rev 02)
Subsystem: DViCO Corporation Unknown device d500
Flags: bus master, fast devsel, latency 0, IRQ 5
Memory at fa800000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express Endpoint IRQ 0
Capabilities: [80] Power Management version 2
Capabilities: [90] Vital Product Data
Capabilities: [a0] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable- ...
==============================
$> cat /proc/interrupts
CPU0 CPU1
0: 19755702 0 IO-APIC-edge timer
1: 10 0 IO-APIC-edge i8042
6: 3 0 IO-APIC-edge floppy
8: 0 0 IO-APIC-edge rtc
9: 0 0 IO-APIC-fasteoi acpi
12: 4 0 IO-APIC-edge i8042
14: 423145 0 IO-APIC-edge ide0
15: 708464 0 IO-APIC-edge ide1
17: 8497107 0 IO-APIC-fasteoi nvidia
18: 3889131 0 IO-APIC-fasteoi Technisat/B2C2 FlexCop
II/IIb/III Digital TV PCI Driver
19: 2 0 IO-APIC-fasteoi ohci1394
20: 6393 0 IO-APIC-fasteoi ohci_hcd:usb2
21: 14 0 IO-APIC-fasteoi ehci_hcd:usb1
22: 86778 0 IO-APIC-fasteoi libata
23: 8229107 0 IO-APIC-fasteoi HDA Intel, eth0
NMI: 5335 7502
LOC: 19756623 19757158
ERR: 0
==============================
If any more information is wanted, please let me know. If this information is
useless and unhelpful, then I apologize in advance.
--James Evans
_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
