The mailer cut half my mail off, as I put a single dot on a line, so here it is again:
Thanks to John and Jesper for the prompt reply. I tried that, and things looks a little different. I do this on one screen and leave it running: tzap -a 0 -r "BBC ONE" using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' reading channels from file '/root/.tzap/channels.conf' tuning to 505833330 Hz video pid 0x0258, audio pid 0x0259 status 0d | signal 3030 | snr dddd | ber 000064e9 | unc 0000000a | status 1f | signal 3030 | snr ebeb | ber 0000003e | unc 00000000 | FE_HAS_LOCK status 1f | signal 3030 | snr ebeb | ber 0000003f | unc 00000000 | FE_HAS_LOCK status 1f | signal 3030 | snr eaea | ber 0000003c | unc 00000000 | FE_HAS_LOCK status 1f | signal 3030 | snr e9e9 | ber 0000004a | unc 00000000 | FE_HAS_LOCK status 1f | signal 3030 | snr eaea | ber 00000048 | unc 00000000 | FE_HAS_LOCK etc, etc and this on another one: [EMAIL PROTECTED] dvbstream]# ./dvbstream -ps -qam 16 -cr 3_4 600 601 | mplayer - dvbstream v0.6 - (C) Dave Chapman 2001-2004 Released under the GPL. Latest version available from http://www.linuxstb.org/ dvbstream will stop after -1 seconds (71582788 minutes) Setting filter for PID 600 Setting filter for PID 601 Using 224.0.1.2:5004:2 version=2 Streaming 2 streams MPlayer 1.0pre4-3.3.3 (C) 2000-2004 MPlayer Team CPU: Intel Celeron 2/Pentium III Coppermine,Geyserville 870.7 MHz (Family: 6, Stepping: 10) Detected cache-line size is 32 bytes CPUflags: MMX: 1 MMX2: 1 3DNow: 0 3DNow2: 0 SSE: 1 SSE2: 0 Reading config file /etc/mplayer/mplayer.conf Reading config file /root/.mplayer/config Reading /root/.mplayer/codecs.conf: Can't open '/root/.mplayer/codecs.conf': No such file or directory Reading /etc/mplayer/codecs.conf: Can't open '/etc/mplayer/codecs.conf': No such file or directory Using built-in default codecs.conf. font: can't open file: /root/.mplayer/font/font.desc Audiostream: Layer: 2 BRate: 256 kb/s Freq: 48.0 kHz Font /usr/share/mplayer/font/font.desc loaded successfully! (206 chars) Using Linux hardware RTC timing (1024Hz). Can't open input config file /root/.mplayer/input.conf: No such file or directory Can't open input config file /etc/mplayer/input.conf: No such file or directory Falling back on default (hardcoded) input config Opening joystick device /dev/input/js0 Can't open joystick device /dev/input/js0 : No such device Can't init input joystick Setting up LIRC support... mplayer: could not connect to socket mplayer: No such file or directory Failed to open LIRC support. You will not be able to use your remote control. Playing -. Reading from stdin... Videostream: ASPECT: 16:9 Size = 720x576 FRate: 25 fps BRate: 4.35 Mbit/s However, no actual screen appears!! Also, I can hear nothing but hissing through the speakers... Mike
