On 1/16/2018 11:25 PM, Bjorn Andersson wrote:
On Fri 12 Jan 17:05 PST 2018, Karthikeyan Ramasubramanian wrote:
Add device tree binding support for the QCOM GENI SE driver.
Signed-off-by: Karthikeyan Ramasubramanian <krama...@codeaurora.org>
Better describe the entire GENI, with it's functions in the same
binding.
Ok.
---
.../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
new file mode 100644
index 0000000..66f8a16
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
@@ -0,0 +1,34 @@
+Qualcomm Technologies, Inc. GENI Serial Engine QUP Wrapper Controller
+
+Generic Interface (GENI) based Qualcomm Universal Peripheral (QUP) wrapper
+is a programmable module for supporting a wide range of serial interfaces
+like UART, SPI, I2C, I3C, etc. A single QUP module can provide upto 8 Serial
+Interfaces, using its internal Serial Engines. The GENI Serial Engine QUP
+Wrapper controller is modeled as a node with zero or more child nodes each
+representing a serial engine.
+
+Required properties:
+- compatible: Must be "qcom,geni-se-qup".
+- reg: Must contain QUP register address and length.
+- clock-names: Must contain "m-ahb" and "s-ahb".
+- clocks: AHB clocks needed by the device.
+
+Required properties if child node exists:
+- #address-cells: Must be 1
+- #size-cells: Must be 1
But on a 64-bit system, shouldn't these be 2?
As pointed out by Rob in his response, the module size is less than 4G
and hence 1.
+- ranges: Must be present
+
+Properties for children:
+
+A GENI based QUP wrapper controller node can contain 0 or more child nodes
+representing serial devices. These serial devices can be a QCOM UART, I2C
+controller, spi controller, or some combination of aforementioned devices.
+
+Example:
+ qup0: qcom,geniqup0@8c0000 {
I don't see a reason for this to be referenced, so skip the label. And
don't use qcom, in the node name; "geni" would be perfectly fine?
Ok.
+ compatible = "qcom,geni-se-qup";
+ reg = <0x8c0000 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ }
Regards,
Bjorn
Regards,
Karthik.
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
