Prezados Amigos,
estou montando um servidor linux e estou com um problema com uma
placa Paralela/Serial PCI que o linux nao esta reconhecendo. Ja
pesquisei pra cacete na internet e vi que tem um monte de gente com o
mesmo problema mas ninguem responde diretamente como resolver isto.
Ericsson tu que o linuxer mais antigo tens alguma dica ? Abaixo esta
o resultado dos comandos: lspci -vv, cat /proc/pci,
dmesg, lsmod, cat /etc/conf.modules e um teste que fiz imprimindo
direto pra porta. A impressora funciona beleza com uma placa ISA. Ah
a serial tambem nao esta funcinando.
Ja entrei na pagina de Tim Waugh mas nada. Ele fala para atualizar
uns patches e tem arquivo pra cacete. Nao gostaria de relinkar o
kernel pois alem da impressora tenho outra impressora na lp0, um
modem, um pole display, uma placa computone e ta tudo funcionando
menos a placa PCI nova e nao sei o que vai acontecer se relinkar o
Kernel.
Estou com o Red Hat 6.0
Valeu,
Ericson Benjamim.
----------------------------------------------------------------------
====> lspci -vv
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host
bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 64 set
Region 0: Memory at 44000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=21
Command: RQ=31 SBA+ AGP- 64bit- FW- Rate=21
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP
bridge (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: 40000000-408fffff
Prefetchable memory behind bridge: 41000000-41ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 8139
(rev 10)
Subsystem: Unknown device 1259:2500
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 min, 64 max, 66 set
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1400
Region 1: Memory at 40b00000 (32-bit, non-prefetchable)
00:10.0 Serial controller: Lava Computer mfg Inc: Unknown device 0510
(prog-if 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000
00:10.1 Serial controller: Lava Computer mfg Inc: Unknown device 0511
(prog-if 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1008
00:14.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:14.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Region 4: I/O ports at 1820
00:14.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 set
Interrupt: pin D routed to IRQ 0
Region 4: I/O ports at 5800
00:14.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP
[Millennium G200 AGP] (rev 03)
Subsystem: Unknown device 102b:ff03
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16 min, 32 max, 64 set, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 41000000 (32-bit, prefetchable)
Region 1: Memory at 40800000 (32-bit, non-prefetchable)
Region 2: Memory at 40000000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=21
Command: RQ=31 SBA+ AGP- 64bit- FW- Rate=21
----------------------------------------------------------------------
--
===> cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel 440BX - 82443BX Host (rev 3).
Medium devsel. Master Capable. Latency=64.
Prefetchable 32 bit memory at 0x44000000 [0x44000008].
Bus 0, device 1, function 0:
PCI bridge: Intel 440BX - 82443BX AGP (rev 3).
Medium devsel. Master Capable. Latency=64. Min Gnt=140.
Bus 0, device 15, function 0:
Ethernet controller: Realtek 8139 (rev 16).
Medium devsel. Fast back-to-back capable. IRQ 9. Master
Capable. Latency=66. Min Gnt=32.Max Lat=64.
I/O at 0x1400 [0x1401].
Non-prefetchable 32 bit memory at 0x40b00000 [0x40b00000].
Bus 0, device 16, function 0:
Serial controller: Unknown vendor Unknown device (rev 0).
Vendor id=1407. Device id=510.
Slow devsel. Fast back-to-back capable. IRQ 11.
I/O at 0x1000 [0x1001].
Bus 0, device 16, function 1:
Serial controller: Unknown vendor Unknown device (rev 0).
Vendor id=1407. Device id=511.
Slow devsel. Fast back-to-back capable. IRQ 11.
I/O at 0x1008 [0x1009].
Bus 0, device 20, function ISA bridge: Intel 82371AB PIIX4
ISA (rev 2).
Medium devsel. Fast back-to-back capable. Master Capable. No
bursts.
Bus 0, device 20, function 1:
IDE interface: Intel 82371AB PIIX4 IDE (rev 1).
Medium devsel. Fast back-to-back capable. Master Capable.
Latency=64.
I/O at 0x1820 [0x1821].
Bus 0, device 20, function 2:
USB Controller: Intel Unknown device (rev 1).
Vendor id=8086. Device id=7112.
Medium devsel. Fast back-to-back capable. Master Capable.
Latency=64.
I/O at 0x5800 [0x5801].
Bus 0, device 20, function 3:
Bridge: Intel Unknown device (rev 2).
Vendor id=8086. Device id=7113.
Medium devsel. Fast back-to-back capable.
Bus 1, device 0, function 0:
VGA compatible controller: Matrox Matrox G200 AGP (rev 3).
Medium devsel. Fast back-to-back capable. IRQ 9. Master
Capable. Latency=64. Min Gnt=16.Max Lat=32.
Prefetchable 32 bit memory at 0x41000000 [0x41000008].
non-prefetchable 32 bit memory at 0x40800000 [0x40800000].
Non-prefetchable 32 bit memory at 0x40000000 [0x40000000].
----------------------------------------------------------------------
===> dmesg
Linux version 2.2.5-15 (root@bsc148) (gcc version egcs-2.91.66
19990314/Linux (egcs-1.1.2 release)) #1 Mon Mar 20 10:17:18 EST 2000
Detected 547622870 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 545.59 BogoMIPS
Memory: 62788k/65536k available (1040k kernel code, 412k reserved,
912k data, 60k init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel 00/07 stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error
reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.26 (19981001) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xedb20
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Assigning I/O space 5800-581f to device 00:a2
PCI: Enabling I/O for device 00:a2
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
apm: BIOS not found.
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev a1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1820-0x1827, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1828-0x182f, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 51024U2, ATA DISK drive
hdc: LTN323, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 51024U2, 9541MB w/2048kB Cache, CHS=1292/240/63
hdc: ATAPI 32X CD-ROM drive, 120kB Cache
Uniform CDROM driver Revision: 2.54
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: using high-speed MMX checksum routine
pII_mmx : 1334.643 MB/sec
p5_mmx : 1289.304 MB/sec
8regs : 950.595 MB/sec
32regs : 662.559 MB/sec
using fastest function: pII_mmx (1334.643 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
scsi : 0 hosts.
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 60k freed
Adding Swap: 415796k swap-space (priority -1)
rtl8139.c:v1.12 9/14/2000 Donald Becker, [EMAIL PROTECTED]
http://www.scyld.com/network/rtl8139.html
eth0: RealTek RTL8139 Fast Ethernet at 0x1400, IRQ 9,
00:a0:d2:1d:08:e4.
Serial driver version 4.92.SA (2000-1-27) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
LSR safety check engaged!
LSR safety check engaged!
parport0: PC-style at 0x378, irq 7 [SPP,ECP,ECPEPP,ECPPS2]
parport0: Printer, ITHACA SERIES 80E
lp0: using parport0 (interrupt-driven).
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
nfsd_init: initialized fhcache, entries=256
lp0: using parport0 (interrupt-driven).
----------------------------------------------------------------------
===> lsmod
Module Size Used by
lp 4956 0 (autoclean) (unused)
nfsd 151576 8 (autoclean)
lockd 31208 1 (autoclean) [nfsd]
sunrpc 52420 1 (autoclean) [nfsd lockd]
parport_pc 4988 1 (autoclean)
parport 7028 1 (autoclean) [lp parport_pc]
serial 51044 1
rtl8139 11176 1 (autoclean)
pci-scan 2348 0 (autoclean) [rtl8139]
----------------------------------------------------------------------
===> cat /etc/conf.modules
alias scsi_hostadapter aic7xxx
alias eth0 rtl8139
alias parport_lowlevel parport_pc
options parport_pc io=0x378,0x278 irq=7,auto
alias char-major-71 ip2
alias char-major-72 ip2
alias char-major-73 ip2
----------------------------------------------------------------------
===> echo test > /dev/lp1
/dev/lp1: Device not configured
----------------------------------------------------------------------
To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
Seu uso do Yahoo! Groups � sujeito �s regras descritas em:
http://docs.yahoo.com/info/terms/
Assinantes em 15/08/2001: 2265
Mensagens recebidas desde 07/01/1999: 127938
Historico e [des]cadastramento: http://linux-br.conectiva.com.br
Assuntos administrativos e problemas com a lista:
mailto:[EMAIL PROTECTED]
