Opps missed that one rebuild
On Fri, Aug 23, 2013 at 5:05 PM, Christopher Covington <c...@codeaurora.org> wrote: > Hi Phi, > > On 08/23/2013 10:55 AM, Phi Debian wrote: >> Using >> .config - Linux/arm64 3.11.0-rc6 Kernel Configuration >> >> I got >> Device Drivers ---> >> | | [ ] Virtualization drivers (NEW) ---- | | >> | | Virtio drivers ---> | | >> >> >> I enter Virtio drivers as you suggest and I got only 1 line tha tis >> | | < > Platform bus driver for memory mapped virtio devices (NEW) | | >> >> I select all this and save >> >> I check the .config >> CONFIG_VIRTIO=y >> CONFIG_HAS_IOMEM=y >> CONFIG_VIRTIO_MMIO=y >> CONFIG_VIRTIO_BLK=m <<== change this to y >> CONFIG_BLK_DEV=y >> >> make kernel and bootloader >> >> Trying 127.0.0.1... >> Connected to localhost. >> Escape character is '^]'. >> Initializing cgroup subsys cpu >> Linux version 3.11.0-rc6+ (phi@hpfrcu82) (gcc version 4.8.2 20130624 >> (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.07-1 - Linaro GCC >> 2013.07) ) #2 SMP Fri Aug 23 16:34:00 CEST 2013 >> CPU: AArch64 Processor [410fd000] revision 0 >> Machine: Foundation-v8A >> PERCPU: Embedded 10 pages/cpu @ffffffc87ffaa000 s11392 r8192 d21376 u40960 >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1034240 >> Kernel command line: root=/dev/vda2 consolelog=9 rw console=ttyAMA0 >> PID hash table entries: 4096 (order: 3, 32768 bytes) >> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) >> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) >> software IO TLB [mem 0x8f8000000-0x8fc000000] (64MB) mapped at >> [ffffffc878000000-ffffffc87bffffff] >> Memory: 4059816K/4194304K available (3015K kernel code, 200K rwdata, >> 1080K rodata, 167K init, 150K bss, 134488K reserved) >> Virtual kernel memory layout: >> vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB) >> vmemmap : 0xffffffbc01c00000 - 0xffffffbc1f800000 ( 476 MB) >> modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) >> memory : 0xffffffc000000000 - 0xffffffc880000000 ( 34816 MB) >> .init : 0xffffffc000481000 - 0xffffffc0004aac80 ( 168 kB) >> .text : 0xffffffc000080000 - 0xffffffc000480c30 ( 4100 kB) >> .data : 0xffffffc0004ac000 - 0xffffffc0004de0a0 ( 201 kB) >> SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 >> Hierarchical RCU implementation. >> RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. >> NR_IRQS:64 nr_irqs:64 0 >> GIC CPU mask not found - kernel will fail to boot. >> GIC CPU mask not found - kernel will fail to boot. >> Architected local timer running at 100.00MHz (phys). >> Console: colour dummy device 80x25 >> Calibrating delay loop (skipped), value calculated using timer >> frequency.. 200.00 BogoMIPS (lpj=1000000) >> pid_max: default: 32768 minimum: 301 >> Mount-cache hash table entries: 256 >> hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 9 counters available >> CPU1: failed to boot: -38 >> CPU2: failed to boot: -38 >> CPU3: failed to boot: -38 >> Brought up 1 CPUs >> SMP: Total of 1 processors activated (200.00 BogoMIPS). >> devtmpfs: initialized >> atomic64 test passed >> NET: Registered protocol family 16 >> vdso: 2 pages (1 code, 1 data) at base ffffffc0004e0000 >> hw-breakpoint: found 16 breakpoint and 16 watchpoint registers. >> Serial: AMBA PL011 UART driver >> 1c090000.uart: ttyAMA0 at MMIO 0x1c090000 (irq = 37) is a PL011 rev2 >> console [ttyAMA0] enabled >> 1c0a0000.uart: ttyAMA1 at MMIO 0x1c0a0000 (irq = 38) is a PL011 rev2 >> 1c0b0000.uart: ttyAMA2 at MMIO 0x1c0b0000 (irq = 39) is a PL011 rev2 >> 1c0c0000.uart: ttyAMA3 at MMIO 0x1c0c0000 (irq = 40) is a PL011 rev2 >> bio: create slab <bio-0> at 0 >> SCSI subsystem initialized >> Switched to clocksource arch_sys_counter >> NET: Registered protocol family 2 >> TCP established hash table entries: 32768 (order: 7, 524288 bytes) >> TCP bind hash table entries: 32768 (order: 7, 524288 bytes) >> TCP: Hash tables configured (established 32768 bind 32768) >> TCP: reno registered >> UDP hash table entries: 2048 (order: 4, 65536 bytes) >> UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) >> NET: Registered protocol family 1 >> RPC: Registered named UNIX socket transport module. >> RPC: Registered udp transport module. >> RPC: Registered tcp transport module. >> RPC: Registered tcp NFSv4.1 backchannel transport module. >> fuse init (API version 7.22) >> msgmni has been set to 7929 >> io scheduler noop registered >> io scheduler cfq registered (default) >> Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled >> vda: vda1 vda2 >> smc91x: IOADDR ffffff800001c000 doesn't match configuration (300). >> smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <n...@fluxnic.net> >> eth0: SMC91C11xFD (rev 1) at ffffff800001c000 IRQ 47 [nowait] >> eth0: Ethernet addr: 00:02:f7:ef:7e:f2 >> mousedev: PS/2 mouse device common for all mice >> TCP: cubic registered >> NET: Registered protocol family 17 >> EXT3-fs (vda2): error: couldn't mount because of unsupported optional >> features (240) >> EXT2-fs (vda2): error: couldn't mount because of unsupported optional >> features (240) > > Make sure EXT4 support is compiled in as well. > > Regards, > Christopher > > -- > Employee of Qualcomm Innovation Center, Inc. > Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, > hosted by the Linux Foundation. _______________________________________________ linaro-dev mailing list linaro-dev@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-dev
