From: "Ying-Chun Liu (PaulLiu)" <paul....@linaro.org>
Change "reg" to "anatop-reg-offset" due to there is a warning of handling no
size field in reg.
This patch also adds the missing device-tree binding documentation.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul....@linaro.org>
Cc: Shawn Guo <shawn....@linaro.org>
Cc: Mark Brown <broo...@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <l...@ti.com>
---
.../bindings/regulator/anatop-regulator.txt | 29 ++++++++++++++++++++
drivers/regulator/anatop-regulator.c | 5 ++-
2 files changed, 32 insertions(+), 2 deletions(-)
create mode 100644
Documentation/devicetree/bindings/regulator/anatop-regulator.txt
diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt
b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt
new file mode 100644
index 0000000..357758c
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt
@@ -0,0 +1,29 @@
+Anatop Voltage regulators
+
+Required properties:
+- compatible: Must be "fsl,anatop-regulator"
+- anatop-reg-offset: Anatop MFD register offset
+- anatop-vol-bit-shift: Bit shift for the register
+- anatop-vol-bit-width: Number of bits used in the register
+- anatop-min-bit-val: Minimum value of this register
+- anatop-min-voltage: Minimum voltage of this regulator
+- anatop-max-voltage: Maximum voltage of this regulator
+
+Any property defined as part of the core regulator
+binding, defined in regulator.txt, can also be used.
+
+Example:
+
+ regulator-vddpu {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddpu";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <9>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1300000>;
+ };
diff --git a/drivers/regulator/anatop-regulator.c
b/drivers/regulator/anatop-regulator.c
index 17499a5..53969af 100644
--- a/drivers/regulator/anatop-regulator.c
+++ b/drivers/regulator/anatop-regulator.c
@@ -138,9 +138,10 @@ static int __devinit anatop_regulator_probe(struct
platform_device *pdev)
rdesc->type = REGULATOR_VOLTAGE;
rdesc->owner = THIS_MODULE;
sreg->mfd = anatopmfd;
- ret = of_property_read_u32(np, "reg", &sreg->control_reg);
+ ret = of_property_read_u32(np, "anatop-reg-offset",
+ &sreg->control_reg);
if (ret) {
- dev_err(dev, "no reg property set\n");
+ dev_err(dev, "no anatop-reg-offset property set\n");
goto anatop_probe_end;
}
ret = of_property_read_u32(np, "anatop-vol-bit-width",
--
1.7.9.1
_______________________________________________
linaro-dev mailing list
linaro-dev@lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-dev
