Panda Testing update:
Booting on panda seems to be fine but sd/mmc dumps lot of I/O errors on
console.
Tested with device tree enabled and disabled. With device tree enable, the
MMC I/O
errors are more. Tried with multiple SD cards with different brands.
Not sure if there is any bug already listed for this issue.
Log:
Texas Instruments X-Loader 1.5.0 (Apr 11 2011 - 09:48:22)
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2011.03 (May 25 2011 - 17:23:48)
CPU : OMAP4430
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
Using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 3 0
Panda #
Panda # mmc rescan 0
Panda # setenv dtbaddr 0x81600000
Panda # setenv bootcmd 'fatload mmc 0:1 0x80000000 uImage; fatload mmc 0:1
0x81700000 uInitrd; fatload mmc 0:1 ${dtbaddr} panda.dtb; fdt addr
${dtbaddr}; fdt resize; bootm 0x80000000 0x81700000 ${dtbaddr}'
Panda # setenv bootargs ' console=tty0 console=ttyO2,115200n8 root=/init
rootwait ro earlyprintk'
Panda # boot
reading uImage
8230292 bytes read
reading uInitrd
4761795 bytes read
reading panda.dtb
344 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Linux-2.6.38.7
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8230228 Bytes = 7.8 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81700000 ...
Image Name: initramfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 4761731 Bytes = 4.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 81600000
Booting using the fdt blob at 0x81600000
Loading Kernel Image ... OK
OK
reserving fdt memory region: addr=9d000000 size=3000000
reserving fdt memory region: addr=b0000000 size=10000000
reserving fdt memory region: addr=81600000 size=1000
Loading Ramdisk to afb75000, end affff883 ... OK
Loading Device Tree to afb71000, end afb74fff ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.38.7 (linaro@linaro-pc) (gcc version 4.5.2
(Ubuntu/Linaro 4.5.2-8ubuntu3) ) #5 SMP Thu May 26 11:47:07 IST 2011
[ 0.000000] CPU: ARMv7 Processor [411fc092] revision 2 (ARMv7),
cr=10c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction
cache
[ 0.000000] Machine: OMAP4 Panda board, model: TI OMAP4 PandaBoard
[ 0.000000] Reserving 33554432 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] OMAP_TAP_DIE_ID_0: 0x01000000
[ 0.000000] OMAP_TAP_DIE_ID_1: 0x0612d687
[ 0.000000] OMAP_TAP_DIE_ID_2: 0x00000001
[ 0.000000] OMAP_TAP_DIE_ID_3: 0x1d620003
[ 0.000000] OMAP4430 ES2.1
[ 0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0xe000
[ 0.000000] powerdomain: waited too long for powerdomain dss_pwrdm to
complete transition
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c2077000 s10336 r8192 d14240
u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 251904
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
root=/init rootwait ro earlyprintk
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Memory: 730MB 262MB = 992MB total
[ 0.000000] Memory: 665744k/665744k available, 382832k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xf0800000 - 0xf8000000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0c56000 (12600 kB)
[ 0.000000] .text : 0xc0c56000 - 0xc12993e4 (6413 kB)
[ 0.000000] .data : 0xc129a000 - 0xc1309550 ( 446 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:410
[ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for
dpll_mpu_m2_ck.
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc.,
Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.001098] Calibrating delay loop... 2009.29 BogoMIPS (lpj=7847936)
[ 0.171905] pid_max: default: 32768 minimum: 301
[ 0.172546] Security Framework initialized
[ 0.172912] Mount-cache hash table entries: 512
[ 0.176361] CPU: Testing write buffer coherency: ok
[ 0.177154] Calibrating local timer... 491.91MHz.
[ 0.218963] L310 cache controller enabled
[ 0.218994] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000,
Cache size: 1048576 B
[ 0.221252] CPU1: Booted secondary processor
[ 0.221252] CPU1: Unknown IPI message 0x1
[ 0.402038] Brought up 2 CPUs
[ 0.402069] SMP: Total of 2 processors activated (3972.37 BogoMIPS).
[ 0.403137] devtmpfs: initialized
[ 0.409606] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
emif_fw
[ 0.409637] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_instr
[ 0.409667] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_main_1
[ 0.409667] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l3_main_2
[ 0.409698] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_abe
[ 0.409729] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_cfg
[ 0.409729] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_per
[ 0.409759] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_wkup
[ 0.409759] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
mpu_private
[ 0.409790] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for dsp
[ 0.409820] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for ipu
[ 0.410095] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
[ 0.415466] print_constraints: dummy:
[ 0.416137] NET: Registered protocol family 16
[ 0.416656] GPMC revision 6.0
[ 0.419982] omap_device: omap_gpio.0: new worst case activate latency 0:
61035
[ 0.420288] OMAP GPIO hardware version 0.1
[ 0.420532] OMAP GPIO hardware version 0.1
[ 0.420745] OMAP GPIO hardware version 0.1
[ 0.420959] OMAP GPIO hardware version 0.1
[ 0.421173] OMAP GPIO hardware version 0.1
[ 0.421386] OMAP GPIO hardware version 0.1
[ 0.427124] omap_mux_init: Add partition: #1: core, flags: 2
[ 0.428527] omap_mux_init: Add partition: #2: wkup, flags: 2
[ 0.431365] omap_device: omap_uart.0: new worst case activate latency 0:
30517
[ 0.438415] No ATAGs?
[ 0.438446] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.438446] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint
single-step.
[ 0.438476] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.445098] pm_dbg_init: only OMAP3 supported
[ 0.445678] OMAP DMA hardware revision 0.0
[ 0.479553] bio: create slab <bio-0> at 0
[ 0.482147] print_constraints: vwl1271: 1800 mV
[ 0.484588] SCSI subsystem initialized
[ 0.484893] omap_device: omap2_mcspi.1: new worst case activate latency
0: 30517
[ 0.485595] omap_device: omap2_mcspi.1: new worst case deactivate latency
0: 30517
[ 0.488830] usbcore: registered new interface driver usbfs
[ 0.489288] usbcore: registered new interface driver hub
[ 0.489593] usbcore: registered new device driver usb
[ 0.501098] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
[ 0.517395] Skipping twl internal clock init and using bootloader value
(unknown osc rate)
[ 0.518280] twl6030: PIH (irq 39) chaining IRQs 368..387
[ 0.540252] print_constraints: VUSB: 3300 mV normal standby
[ 0.760681] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
[ 0.761718] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV normal
standby
[ 0.762908] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal
standby
[ 0.763977] print_constraints: VANA: 2100 mV normal standby
[ 0.764953] print_constraints: VCXIO: 1800 mV normal standby
[ 0.765991] print_constraints: VDAC: 1800 mV normal standby
[ 0.767150] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV
normal standby
[ 0.768402] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV
normal standby
[ 0.769409] print_constraints: CLK32KG:
[ 0.769744] omap_device: omap_i2c.1: new worst case deactivate latency 0:
30517
[ 0.769836] omap_device: omap_i2c.2: new worst case activate latency 0:
30517
[ 0.782897] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
[ 0.798126] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[ 0.813385] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
[ 0.815307] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.817260] Bluetooth: Core ver 2.15
[ 0.817504] NET: Registered protocol family 31
[ 0.817535] Bluetooth: HCI device and connection manager initialized
[ 0.817596] Bluetooth: HCI socket layer initialized
[ 0.819824] cfg80211: Calling CRDA to update world regulatory domain
[ 0.821105] Switching to clocksource 32k_counter
[ 0.823394] Switched to NOHz mode on CPU #1
[ 0.828582] Switched to NOHz mode on CPU #0
[ 0.871917] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host),
debug=0
[ 0.872131] omap_device: musb-omap2430.-1: new worst case activate
latency 0: 30517
[ 0.872680] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000
using DMA, IRQ 124
[ 0.873199] omap_device: musb-omap2430.-1: new worst case deactivate
latency 0: 30517
[ 0.873413] NET: Registered protocol family 2
[ 0.873779] IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.874877] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 0.877258] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 0.893524] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.893676] TCP reno registered
[ 0.893707] UDP hash table entries: 512 (order: 3, 40960 bytes)
[ 0.893981] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[ 0.894989] NET: Registered protocol family 1
[ 0.895751] RPC: Registered udp transport module.
[ 0.895782] RPC: Registered tcp transport module.
[ 0.895782] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.157226] Trying to unpack rootfs image as initramfs...
[ 1.461700] Freeing initrd memory: 4648K
[ 1.461730] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.467132] omap_init_opp_table: no hwmod or odev for iva, [6] cannot add
OPPs.
[ 1.476074] LTTng will clear ccnt top bit every 136 jiffies.
[ 1.587341] VFS: Disk quotas dquot_6.5.2
[ 1.587554] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.588836] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat,
Inc.
[ 1.589508] msgmni has been set to 1309
[ 1.591888] io scheduler noop registered
[ 1.591918] io scheduler deadline registered
[ 1.592010] io scheduler cfq registered (default)
[ 1.657348] OMAP DSS rev 4.0
[ 1.833862] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.040863] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP
UART0
[ 2.087036] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP
UART1
[ 2.133911] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP
UART2
[ 3.102050] console [ttyO2] enabled
[ 3.157348] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP
UART3
[ 3.275909] brd: module loaded
[ 3.304138] loop: module loaded
[ 3.320861] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 3.327850] omap2-nand driver initializing
[ 3.332824] OneNAND driver initializing
[ 3.355163] usbcore: registered new interface driver asix
[ 3.363708] usbcore: registered new interface driver cdc_ether
[ 3.370361] usbcore: registered new interface driver smsc95xx
[ 3.376983] usbcore: registered new interface driver net1080
[ 3.383331] usbcore: registered new interface driver cdc_subset
[ 3.389984] usbcore: registered new interface driver zaurus
[ 3.395904] cdc_ncm: 7-Feb-2011
[ 3.399688] usbcore: registered new interface driver cdc_ncm
[ 3.407043] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.414245] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 3.423339] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 3.470153] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
[ 3.485473] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.491943] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.499084] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.506683] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.512298] usb usb1: Manufacturer: Linux 2.6.38.7 ehci_hcd
[ 3.518157] usb usb1: SerialNumber: ehci-omap.0
[ 3.526214] hub 1-0:1.0: USB hub found
[ 3.530242] hub 1-0:1.0: 3 ports detected
[ 3.563995] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.570678] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller
[ 3.577789] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned bus
number 2
[ 3.618286] ohci-omap3 ohci-omap3.0: irq 108, io mem 0x4a064800
[ 3.700531] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.707702] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.715301] usb usb2: Product: OMAP3 OHCI Host Controller
[ 3.720977] usb usb2: Manufacturer: Linux 2.6.38.7 ohci_hcd
[ 3.726837] usb usb2: SerialNumber: ohci-omap3.0
[ 3.733459] hub 2-0:1.0: USB hub found
[ 3.737701] hub 2-0:1.0: 3 ports detected
[ 3.746582] usbcore: registered new interface driver cdc_wdm
[ 3.752563] Initializing USB Mass Storage driver...
[ 3.760711] usbcore: registered new interface driver usb-storage
[ 3.767059] USB Mass Storage support registered.
[ 3.772796] usbcore: registered new interface driver libusual
[ 3.860473] usb 1-1: new high speed USB device number 2 using ehci-omap
[ 4.493103] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 4.500183] usb 1-1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.509857] hub 1-1:1.0: USB hub found
[ 4.516387] hub 1-1:1.0: 5 ports detected
[ 4.565307] usbcore: registered new interface driver usbtest
[ 4.575378] mousedev: PS/2 mouse device common for all mice
[ 4.594390] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 4.604888] i2c /dev entries driver
[ 4.620788] lirc_dev: IR Remote Control driver registered, major 251
[ 4.627777] IR NEC protocol handler initialized
[ 4.632537] IR RC5(x) protocol handler initialized
[ 4.637603] IR RC6 protocol handler initialized
[ 4.642364] IR JVC protocol handler initialized
[ 4.647125] IR Sony protocol handler initialized
[ 4.652008] IR RC5 (streamzap) protocol handler initialized
[ 4.657867] IR LIRC bridge handler initialized
[ 4.662536] Linux video capture interface: v2.00
[ 4.671081] Driver for 1-wire Dallas network protocol.
[ 4.680389] omap_device: omap_wdt.-1: new worst case activate latency 0:
30517
[ 4.689910] OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[ 4.696258] omap_device: omap_wdt.-1: new worst case deactivate latency
0: 30517
[ 4.706909] Bluetooth: HCI UART driver ver 2.2
[ 4.711578] Bluetooth: HCI H4 protocol initialized
[ 4.716644] Bluetooth: HCI BCSP protocol initialized
[ 4.721893] Bluetooth: HCILL protocol initialized
[ 4.729980] cpuidle: using governor ladder
[ 4.734313] cpuidle: using governor menu
[ 4.745391] _regulator_get: omap_hsmmc.0 supply vmmc_aux not found, using
dummy regulator
[ 4.756042] _regulator_get: omap_hsmmc.4 supply vmmc_aux not found, using
dummy regulator
[ 4.774139] usbcore: registered new interface driver usbhid
[ 4.780059] usbhid: USB HID core driver
[ 4.794128] OMAP4 HDMI audio SoC init
[ 4.800506] asoc: omap4-hdmi-audio-codec <-> hdmi-audio-dai mapping ok
[ 4.814910] ALSA device list:
[ 4.818115] #0: PandaHDMI
[ 4.821044] oprofile: hardware counters not available
[ 4.826385] oprofile: using timer interrupt.
[ 4.831359] TCP cubic registered
[ 4.834808] Initializing XFRM netlink socket
[ 4.839416] NET: Registered protocol family 17
[ 4.844177] NET: Registered protocol family 15
[ 4.849060] Bluetooth: L2CAP ver 2.15
[ 4.853027] Bluetooth: L2CAP socket layer initialized
[ 4.858367] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.863342] usb 1-1.1: new high speed USB device number 3 using ehci-omap
[ 4.863342] Bluetooth: SCO socket layer initialized
[ 4.863555] Bluetooth: RFCOMM TTY layer initialized
[ 4.863586] Bluetooth: RFCOMM socket layer initialized
[ 4.863586] Bluetooth: RFCOMM ver 1.11
[ 4.863586] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.863586] Bluetooth: BNEP filters: protocol multicast
[ 4.863616] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 4.864654] lib80211: common routines for IEEE802.11 drivers
[ 4.864715] Registering the dns_resolver key type
[ 4.865020] VFP support v0.3: implementor 41 architecture 3 part 30
variant 9 rev 1
[ 4.927185] ThumbEE CPU extension supported.
[ 4.931762] Registering SWP/SWPB emulation handler
[ 4.943847] omap2_set_init_voltage: Invalid parameters!
[ 4.949523] omap2_set_init_voltage: Unable to put vdd_iva to its init
voltage
[ 4.949523]
[ 4.964599] Power Management for TI OMAP4.
[ 4.969146] sr_init: No PMIC hook to init smartreflex
[ 4.974884] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver
initialized
[ 4.983428] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver
initialized
[ 4.992004] smartreflex smartreflex.2: omap_sr_probe: SmartReflex driver
initialized
[ 5.000946] SmartReflex Class3 initialized
[ 5.041473] usb 1-1.1: New USB device found, idVendor=0424,
idProduct=ec00
[ 5.048736] usb 1-1.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 5.076873] smsc95xx v1.0.4
[ 5.090881] Console: switching to colour frame buffer device 80x30
[ 5.110260] mmc0: host does not support reading read-only switch.
assuming write-enable.
[ 5.133941] mmc0: new SD card at address c71c
[ 5.139984] mmcblk0: mmc0:c71c SD01G 982 MiB
[ 5.146911] mmcblk0: retrying using single block read
[ 5.147186] mmcblk0: error -84 transferring data, sector 0, nr 8, card
status 0x900
[ 5.147186] end_request: I/O error, dev mmcblk0, sector 0
[ 5.147460] mmcblk0: error -84 transferring data, sector 1, nr 7, card
status 0x900
[ 5.147460] end_request: I/O error, dev mmcblk0, sector 1
[ 5.147735] mmcblk0: error -84 transferring data, sector 2, nr 6, card
status 0x900
[ 5.147735] end_request: I/O error, dev mmcblk0, sector 2
[ 5.148010] mmcblk0: error -84 transferring data, sector 3, nr 5, card
status 0x900
[ 5.148010] end_request: I/O error, dev mmcblk0, sector 3
[ 5.148254] mmcblk0: error -84 transferring data, sector 4, nr 4, card
status 0x900
[ 5.148284] end_request: I/O error, dev mmcblk0, sector 4
[ 5.148529] mmcblk0: error -84 transferring data, sector 5, nr 3, card
status 0x900
[ 5.148529] end_request: I/O error, dev mmcblk0, sector 5
[ 5.148834] mmcblk0: error -84 transferring data, sector 6, nr 2, card
status 0x900
[ 5.148834] end_request: I/O error, dev mmcblk0, sector 6
[ 5.149078] mmcblk0: error -84 transferring data, sector 7, nr 1, card
status 0x900
[ 5.149108] end_request: I/O error, dev mmcblk0, sector 7
[ 5.149200] Buffer I/O error on device mmcblk0, logical block 0
[ 5.150054] mmcblk0: retrying using single block read
[ 5.150634] mmcblk0: error -84 transferring data, sector 0, nr 8, card
status 0x900
[ 5.150695] end_request: I/O error, dev mmcblk0, sector 0
[ 5.151031] mmcblk0: error -84 transferring data, sector 1, nr 7, card
status 0x900
[ 5.151062] end_request: I/O error, dev mmcblk0, sector 1
[ 5.151397] mmcblk0: error -84 transferring data, sector 2, nr 6, card
status 0x900
[ 5.151397] end_request: I/O error, dev mmcblk0, sector 2
[ 5.151763] mmcblk0: error -84 transferring data, sector 3, nr 5, card
status 0x900
[ 5.151763] end_request: I/O error, dev mmcblk0, sector 3
[ 5.152130] mmcblk0: error -84 transferring data, sector 4, nr 4, card
status 0x900
[ 5.152130] end_request: I/O error, dev mmcblk0, sector 4
[ 5.152526] mmcblk0: error -84 transferring data, sector 5, nr 3, card
status 0x900
[ 5.152526] end_request: I/O error, dev mmcblk0, sector 5
[ 5.152893] mmcblk0: error -84 transferring data, sector 6, nr 2, card
status 0x900
[ 5.152893] end_request: I/O error, dev mmcblk0, sector 6
[ 5.153259] mmcblk0: error -84 transferring data, sector 7, nr 1, card
status 0x900
[ 5.153289] end_request: I/O error, dev mmcblk0, sector 7
[ 5.153289] Buffer I/O error on device mmcblk0, logical block 0
[ 5.153381] mmcblk0: unable to read partition table
- Manjunath
On Wed, May 25, 2011 at 8:12 AM, Deepak Saxena <[email protected]> wrote:
> Hi all,
>
> The Kernel Working Group is getting ready to release the first of our new
> monthly development snapshot in a few days and we would like folks
> to do some quick sanity boot testing on their boards. Please
> grab or update the kernel from
> git://git.linaro.org/kernel/linux-linaro-2.6.38.git,
> and checkout the linaro-11.05-2.6.38 tag (which happens to be same
> as master at this moment) and give it a quick spin. Note that this is just
> the stock Linaro kernel and does not include any binary graphics drivers
> or other bits provided by Linaro's landing team kernels, so we just
> need the basic build and boot tested along with some simple
> testing of devices that can be used w/o extra drivers.
>
> Thanks!
> ~Deepak
>
> _______________________________________________
> linaro-kernel mailing list
> [email protected]
> http://lists.linaro.org/mailman/listinfo/linaro-kernel
>
_______________________________________________
linaro-dev mailing list
[email protected]
http://lists.linaro.org/mailman/listinfo/linaro-dev
