The id_entry will possibly be NULL, So, need check
id_entry and make sure it not NULL before using it.
Signed-off-by: Jason Liu <r64...@freescale.com>
---
drivers/net/fec.c | 12 ++++++------
1 files changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/net/fec.c b/drivers/net/fec.c
index 2a71373..02cdd71 100644
--- a/drivers/net/fec.c
+++ b/drivers/net/fec.c
@@ -293,7 +293,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device
*dev)
* the system that it's running on. As the result, driver has to
* swap every frame going to and coming from the controller.
*/
- if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
+ if (id_entry && id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
swap_buffer(bufaddr, skb->len);
/* Save skb pointer */
@@ -529,7 +529,7 @@ fec_enet_rx(struct net_device *dev)
dma_unmap_single(NULL, bdp->cbd_bufaddr, bdp->cbd_datlen,
DMA_FROM_DEVICE);
- if (id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
+ if (id_entry && id_entry->driver_data & FEC_QUIRK_SWAP_FRAME)
swap_buffer(data, pkt_len);
/* This does 16 byte alignment, exactly what we need.
@@ -808,7 +808,7 @@ static int fec_enet_mii_init(struct platform_device *pdev)
* mdio interface in board design, and need to be configured by
* fec0 mii_bus.
*/
- if ((id_entry->driver_data & FEC_QUIRK_ENET_MAC) && pdev->id) {
+ if (id_entry && (id_entry->driver_data & FEC_QUIRK_ENET_MAC) &&
pdev->id) {
/* fec1 uses fec0 mii_bus */
fep->mii_bus = fec0_mii_bus;
return 0;
@@ -851,7 +851,7 @@ static int fec_enet_mii_init(struct platform_device *pdev)
goto err_out_free_mdio_irq;
/* save fec0 mii_bus */
- if (id_entry->driver_data & FEC_QUIRK_ENET_MAC)
+ if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC)
fec0_mii_bus = fep->mii_bus;
return 0;
@@ -1238,7 +1238,7 @@ fec_restart(struct net_device *dev, int duplex)
* enet-mac reset will reset mac address registers too,
* so need to reconfigure it.
*/
- if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
+ if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
memcpy(&temp_mac, dev->dev_addr, ETH_ALEN);
writel(cpu_to_be32(temp_mac[0]), fep->hwp + FEC_ADDR_LOW);
writel(cpu_to_be32(temp_mac[1]), fep->hwp + FEC_ADDR_HIGH);
@@ -1294,7 +1294,7 @@ fec_restart(struct net_device *dev, int duplex)
* The phy interface and speed need to get configured
* differently on enet-mac.
*/
- if (id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
+ if (id_entry && id_entry->driver_data & FEC_QUIRK_ENET_MAC) {
val = readl(fep->hwp + FEC_R_CNTRL);
/* MII or RMII */
--
1.7.1
_______________________________________________
linaro-dev mailing list
linaro-dev@lists.linaro.org
http://lists.linaro.org/mailman/listinfo/linaro-dev
