That's basically what I do, but using \time. With your example I use:
\relative c'{\partial 8 c8 |
c4 d e f |
\override Staff.TimeSignature #'stencil = ##f \time 7/8 d2 c4. \bar "|." |
}
Since I'm combining Soprano and Alto voices into one staff, this allows me
to put all the timing information in the Soprano voice and have the Alto
voice inherit it.
-tom
On Tue, Apr 7, 2009 at 8:58 AM, Mats Bengtsson <[email protected]>wrote:
>
>
> Tom Dickson wrote:
>
>> I use it to verify I didn't make a mistake in the last measure, especially
>> when I have multiple voices in a single staff.
>>
> ??? If you know that the last measure is incomplete, it's obvious that you
> will get a bar check error if you insert a bar check there. If you really
> want to verify that the last measure is exactly 7/8 long (for example), you
> could explicitly set the measure length manually for that measure:
>
> \relative c'{\partial 8 c8 |
> c4 d e f |
> \set Timing.measureLength = #(ly:make-moment 7 8) d2 c4. | \bar "|."
> }
>
> /Mats
>
>>
>> -tom
>>
>> On Tue, Apr 7, 2009 at 8:27 AM, Mats Bengtsson
>> <[email protected]<mailto:
>> [email protected]>> wrote:
>>
>> Why would you insert a bar check at a place where you know that
>> the measure isn't finished?
>> Bar checks are only intended to help you make sure that LilyPond
>> thinks that the measure is
>> finished at the same place as you think it is.
>>
>> If you want an ending bar line, just use \bar "|." (or whatever
>> bar type you wish) but not a bar check.
>>
>> /Mats
>>
>> Tom Dickson wrote:
>>
>> A feature I would like is to make it so that barchecks don't
>> fail on the end of a staff started with \partial. Especially
>> in songs, the last measure will usually be cut down by the
>> same amount as the \partial at the beginning. Currently I have
>> to hide the time signature and change time at the end of the
>> staff to make it look right.
>>
>> Other than that Lilypond has worked wonderfully for our
>> booklet we're making. Thanks!
>>
>> -tom
>>
>>
>> _______________________________________________
>> lilypond-user mailing list
>> [email protected] <mailto:[email protected]>
>> http://lists.gnu.org/mailman/listinfo/lilypond-user
>>
>>
>> -- =============================================
>> Mats Bengtsson
>> Signal Processing
>> School of Electrical Engineering
>> Royal Institute of Technology (KTH)
>> SE-100 44 STOCKHOLM
>> Sweden
>> Phone: (+46) 8 790 8463 Fax:
>> (+46) 8 790 7260
>> Email: [email protected]
>> <mailto:[email protected]>
>> WWW: http://www.s3.kth.se/~mabe <http://www.s3.kth.se/%7Emabe><
>> http://www.s3.kth.se/%7Emabe>
>> =============================================
>>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> lilypond-user mailing list
>> [email protected]
>> http://lists.gnu.org/mailman/listinfo/lilypond-user
>>
>>
>
> --
> =============================================
> Mats Bengtsson
> Signal Processing
> School of Electrical Engineering
> Royal Institute of Technology (KTH)
> SE-100 44 STOCKHOLM
> Sweden
> Phone: (+46) 8 790 8463
> Fax: (+46) 8 790 7260
> Email: [email protected]
> WWW: http://www.s3.kth.se/~mabe <http://www.s3.kth.se/%7Emabe>
> =============================================
>
>
_______________________________________________
lilypond-user mailing list
[email protected]
http://lists.gnu.org/mailman/listinfo/lilypond-user
