Em 25-11-2013 13:27, Dan McGhee escreveu: > Please excuse the "top post." I've done it for a reason. > > Alan, you have gotten a number of great suggestions from some really > helpful people. I think, however, that the waters are very muddy right > now. The main problem is that your system can't find your ethernet > card--eth0. That's the first goal. After your system sees and > acknowledges it's existence, then troubleshoot connecting if any > problems persist.
It can find the interface. Replying to Ken, Alan wrote: Em 24-11-2013 14:04, Alan Feuerbacher escreveu: > On 11/24/2013 10:48 AM, Ken Moffat wrote: >> > I think Alan needs the r8169, this is what I use : >> > >> > CONFIG_NET_VENDOR_REALTEK=y >> > and >> > CONFIG_R8169=m (actually 'y' would be better, i.e. faster to come >> > up) > Ok, I set that and recompiled the kernel. No luck; the eth0 interface > will not come up. > > Alan Then more recently he sent a post to which I replied, in which the interface was there: Em 25-11-2013 11:59, Alan Feuerbacher escreveu: > On 11/24/2013 2:33 PM, Pierre Labastie wrote: >> Le 24/11/2013 19:24, David Kredba a écrit : >>>> Per Ken's suggestion, I added the ethernet driver for my Realtek >>>> ethernet device, recompiled the kernel, reinstalled systemd/udev from >>>> scratch. Still no luck. >>>> >>>> When linux starts, I see a message: >>>> "Bringing up the eth0 interface... skipped" >>>> >>>> When I try to bring up the network with ifup I get this: >>>> >>>> ifup eth0 >>>> ####### >>>> Bringing up the eth0 interface... >>>> Adding IPv4 address 10.0.1.1 to the eth0 interface...Cannot find >>>> device "eth0" >>>> ***** >>>> >>>> *****face eth0 doesn't exist. >>>> ####### This because the name is different, which you find in the same post: >> Before that and if you are still on LFS: >> ip link list > > ####### > 2: p4p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state UP mode DEFAULT group default qlen 1000 > link/ether 30:85:a9:8f:31:09 brd ff:ff:ff:ff:ff:ff > ####### Interface name is p4p1. Only problem is probably he was not aware that crazy name are given to interfaces, now. William suggested how he could fix that. I just use what I get. This is also what says William, Bruce and myself, in other posts. Then other parts of the post confirm that. Finally, I suggested to use: > I think that if you s/etho0/p4p1/ in the /etc/sysconfig/ifconfig.etho > filename and in the file itself, so you would have: > > > cat /etc/sysconfig/ifconfig.p4p1 > > ONBOOT=yes > IFACE=p4p1 > SERVICE=ipv4-static > IP=10.0.1.31 > GATEWAY=10.0.1.1 > PREFIX=24 > BROADCAST=192.168.0.255 William suggested: > Your link name is p4p1. > > You can always look in /sys/class/net, too and see what is there for > your system to use. > > If you want eth0, then follow this thread: > http://www.mail-archive.com/blfs-support@linuxfromscratch.org/msg18294.html > > It'll help you get back to eth0. Otherwise, use whatever name the > kernel gives the device. and Bruce: > You should have a file /etc/sysconfig/ifconfig.eth0 > > ONBOOT=yes > IFACE=p4p1 > SERVICE=ipv4-static > IP=10.0.1.2 # Change to 10.0.1.x to not conflict with other systems > GATEWAY=10.0.1.1 > PREFIX=24 > BROADCAST=10.0.1.255 which is similar to mine, only he suggests > IP=10.0.1.2 # Change to 10.0.1.x to not conflict with other systems and I suggest: > IP=10.0.1.31 My suggestion was based on what dhcp gave to the machine, when running Fedora. It is in Alan's post. -- []s, Fernando -- http://linuxfromscratch.org/mailman/listinfo/lfs-support FAQ: http://www.linuxfromscratch.org/lfs/faq.html Unsubscribe: See the above information page
