20.07.2017 21:02, Oliver Fleischmann:
The WMDR-143N is a small module originally used as a Wifi client in some Loewe smart TV sets. It is sold cheaply at german surplus shops. The module contains a RT3662 SOC.Specifications: - 500 MHz CPU Clock - 1x 10/100Mbps Ethernet (pin header) - 32 MB of RAM - 8 MB of FLASH - 2T3R 2.4/5 GHz (SOC internal) - 3 Antennas on PCB - UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX and RX are 3,3V only! The square hole is pin 1 - Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND) The square hole is pin 1 The original firmware has two identical kernel/rootfs images and two "Factory" calibration data blocks in flash. The LEDE image leaves only the first "Factory" block in place and uses both "Kernel" blocks and the redundant "Factory" block together to gain enough space for the jffs2 partition. Flash instructions: You need UART and Ethernet connections to flash the board. Use the LEDE "sysupgrade.bin" image with tftp. Apply power to the board and in the first 5 seconds, hit 2 to select TFTP upload. The bootloader asks for board- and server IP addresses and filename. Alternate method: With the vendor firmware running, assign an IP address to the ethernet port, tftp the firmware image to /tmp and write to mtd4 ("KernelA"). Signed-off-by: Oliver Fleischmann <o...@bnv-bamberg.de> --- .../linux/ramips/base-files/etc/board.d/02_network | 4 +- target/linux/ramips/base-files/lib/ramips.sh | 3 + .../ramips/base-files/lib/upgrade/platform.sh | 1 + target/linux/ramips/dts/WMDR-143N.dts | 73 ++++++++++++++++++++++ target/linux/ramips/image/rt3883.mk | 8 +++ 5 files changed, 88 insertions(+), 1 deletion(-) create mode 100644 target/linux/ramips/dts/WMDR-143N.dts diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 78ba10342b..fce754e295 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -222,6 +222,7 @@ ramips_setup_interfaces() na930|\ pbr-d1|\ wli-tx4-ag300n|\ + wmdr-143n|\ wmr-300|\ wn3000rpv3|\ wrh-300cr) @@ -333,7 +334,8 @@ ramips_setup_macs()case $board ina5-v11|\ - ht-tm02) + ht-tm02|\ + wmdr-143n) lan_mac=$(cat /sys/class/net/eth0/address) ;; all0239-3g|\ diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 056fab9def..9b02d98ce2 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -589,6 +589,9 @@ ramips_board_detect() { *"WLR-6000") name="wlr-6000" ;; + *"WMDR-143N") + name="wmdr-143n" + ;; *"WMR-300") name="wmr-300" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index e0a260216d..2a2625ca89 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -168,6 +168,7 @@ platform_check_image() { wl-wn575a3|\ wli-tx4-ag300n|\ wlr-6000|\ + wmdr-143n|\ wmr-300|\ wn3000rpv3|\ wnce2001|\ diff --git a/target/linux/ramips/dts/WMDR-143N.dts b/target/linux/ramips/dts/WMDR-143N.dts new file mode 100644 index 0000000000..291f46f856 --- /dev/null +++ b/target/linux/ramips/dts/WMDR-143N.dts @@ -0,0 +1,73 @@ +/dts-v1/; + +#include "rt3883.dtsi" + +/ { + compatible = "loewe,wmdr-143n", "ralink,rt3883-soc"; + model = "Loewe WMDR-143N"; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x00010000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0x7b0000>; + }; + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "jtag", "uartf"; + ralink,function = "gpio"; + }; + }; +};
I added a fix for the pinmux related hang you reported to my staging tree[0]. I've merge your patch with the removed pinmux on top.
Would you please build an image for the Loewe WMDR-143N from my staging tree and report back whether the issue is fixed!
Mathias [0] https://git.lede-project.org/?p=lede/mkresin/staging.git;a=summary _______________________________________________ Lede-dev mailing list Lede-dev@lists.infradead.org http://lists.infradead.org/mailman/listinfo/lede-dev
