CPU: 1.8GHz ARM, RAM: 512MB
Storage: 4MiB Serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, 5 external and 2 internal Port Switch
WiFi: Dualband, ATH10k 2.4GHz, 5GHz MU-MIMO
Signed-off-by: André Valentin <avalen...@marcant.net>
---
.../linux/ipq806x/base-files/etc/board.d/01_leds | 5 +
.../ipq806x/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 6 +
target/linux/ipq806x/base-files/lib/ipq806x.sh | 3 +
.../base-files/lib/preinit/04_set_mtd_ipq806x.sh | 21 ++
.../lib/preinit/05_set_iface_mac_ipq806x.sh | 21 ++
.../ipq806x/base-files/lib/upgrade/platform.sh | 2 +
target/linux/ipq806x/config-4.4 | 18 +-
.../arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts | 338 +++++++++++++++++++++
target/linux/ipq806x/image/Makefile | 26 +-
.../linux/ipq806x/patches-4.4/800-devicetree.patch | 3 +-
.../patches-4.4/999-add-spi-nor-mx25u3235f.patch | 10 +
12 files changed, 449 insertions(+), 8 deletions(-)
create mode 100644
target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
create mode 100644
target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
create mode 100644
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
create mode 100644
target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds
b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index a7ace1f..33774e8 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -33,6 +33,11 @@ ea8500)
ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio"
ucidef_set_led_default "wps" "WPS" "ea8500:green:wps" "0"
;;
+nbg6817)
+ ucidef_set_led_wlan "wifi" "WIFI" "${board}:white:wifi" "phy0radio"
+ ucidef_set_led_wlan "wifi5g" "WIFI5G" "${board}:white:wifi5g"
"phy1radio"
+ ucidef_set_led_netdev "wan" "WAN" "${board}:white:internet" "eth0"
+ ;;
*)
;;
esac
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network
b/target/linux/ipq806x/base-files/etc/board.d/02_network
index b720455..9168ae7 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -35,6 +35,10 @@ ea8500)
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
+nbg6817)
+ ucidef_add_switch "switch0" \
+ "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
+ ;;
*)
echo "Unsupported hardware. Network interfaces not intialized"
;;
diff --git
a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index c7977e6..0a9004f 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -60,6 +60,9 @@ case "$FIRMWARE" in
r7800)
ath10kcal_extract "art" 4096 12064
;;
+ nbg6817)
+ ath10kcal_extract "0:ART" 4096 12064
+ ;;
esac
;;
"ath10k/cal-pci-0001:01:00.0.bin")
@@ -76,6 +79,9 @@ case "$FIRMWARE" in
r7800)
ath10kcal_extract "art" 20480 12064
;;
+ nbg6817)
+ ath10kcal_extract "0:ART" 20480 12064
+ ;;
esac
;;
*)
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh
b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index ea45381..8f3718c 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -38,6 +38,9 @@ ipq806x_board_detect() {
*"R7800")
name="r7800"
;;
+ *"NBG6817")
+ name="nbg6817"
+ ;;
esac
[ -z "$name" ] && name="unknown"
diff --git a/target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
b/target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
new file mode 100644
index 0000000..024cd81
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
@@ -0,0 +1,21 @@
+#
+# Copyright (C) 2009 OpenWrt.org
+#
+
+. /lib/ipq806x.sh
+. /lib/functions/system.sh
+
+preinit_assign_mtd2block() {
+ case $(ipq806x_board_name) in
+ nbg6817)
+ echo "/dev/mmcblk0p2,64KiB,romd" >
/sys/module/block2mtd/parameters/block2mtd
+ echo "/dev/mmcblk0p3,64KiB,header" >
/sys/module/block2mtd/parameters/block2mtd
+ echo "/dev/mmcblk0p4,64KiB,kernel" >
/sys/module/block2mtd/parameters/block2mtd
+ echo "/dev/mmcblk0p6,64KiB,header_1" >
/sys/module/block2mtd/parameters/block2mtd
+ echo "/dev/mmcblk0p7,64KiB,kernel_1" >
/sys/module/block2mtd/parameters/block2mtd
+ echo "/dev/mmcblk0p8,64KiB,rootfs_1" >
/sys/module/block2mtd/parameters/block2mtd
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_assign_mtd2block
diff --git
a/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
b/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
new file mode 100644
index 0000000..b8246ab
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
@@ -0,0 +1,21 @@
+#
+# Copyright (C) 2009 OpenWrt.org
+#
+
+. /lib/ipq806x.sh
+. /lib/functions/system.sh
+
+preinit_set_mac_address() {
+ case $(ipq806x_board_name) in
+ nbg6817)
+ mac_lan=$(dd if=/dev/mtdblock9 bs=1 skip=4 count=65532
2>/dev/null | tr \\0 \\n | grep ^ethaddr= | cut -d= -f2)
+ [ -n "$mac_lan" ] && {
+ ifconfig eth0 hw ether "$mac_lan"
+ mac_wan=$(macaddr_add "$mac_lan" 1)
+ ifconfig eth1 hw ether "$mac_wan"
+ }
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 8768930..dd0cb15 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -9,6 +9,7 @@ platform_check_image() {
ap148 |\
d7800 |\
ea8500 |\
+ nbg6817 |\
r7500 |\
r7500v2 |\
r7800)
@@ -34,6 +35,7 @@ platform_pre_upgrade() {
case "$board" in
ap148 |\
d7800 |\
+ nbg6817 |\
r7500 |\
r7500v2 |\
r7800)
diff --git a/target/linux/ipq806x/config-4.4 b/target/linux/ipq806x/config-4.4
index bc04049..c27a827 100644
--- a/target/linux/ipq806x/config-4.4
+++ b/target/linux/ipq806x/config-4.4
@@ -197,11 +197,6 @@ CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZ4=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_HAVE_NET_DSA=y
@@ -262,6 +257,16 @@ CONFIG_MFD_SYSCON=y
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
CONFIG_MIGHT_HAVE_PCI=y
CONFIG_MIGRATION=y
+CONFIG_MMC=y
+CONFIG_MMC_ARMMMCI=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_MINORS=16
+CONFIG_MMC_QCOM_DML=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_MSM=y
+# CONFIG_MMC_SDHCI_PCI is not set
+CONFIG_MMC_SDHCI_PLTFM=y
+# CONFIG_MMC_TIFM_SD is not set
CONFIG_MODULES_TREE_LOOKUP=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_MSM_GCC_8660=y
@@ -271,6 +276,7 @@ CONFIG_MSM_GCC_8974=y
# CONFIG_MSM_LCC_8960 is not set
CONFIG_MSM_MMCC_8960=y
CONFIG_MSM_MMCC_8974=y
+CONFIG_MTD_BLOCK2MTD=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_M25P80=y
CONFIG_MTD_NAND=y
@@ -378,7 +384,6 @@ CONFIG_QCOM_SCM=y
CONFIG_QCOM_SCM_32=y
# CONFIG_QCOM_SMD is not set
CONFIG_QCOM_SMEM=y
-# CONFIG_QCOM_SPMI_TEMP_ALARM is not set
CONFIG_QCOM_WDT=y
CONFIG_RAS=y
CONFIG_RATIONAL=y
@@ -389,6 +394,7 @@ CONFIG_RD_GZIP=y
CONFIG_REGMAP=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_QCOM_RPM=y
# CONFIG_REGULATOR_QCOM_SPMI is not set
CONFIG_RESET_CONTROLLER=y
diff --git
a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
new file mode 100644
index 0000000..2e1302d
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
@@ -0,0 +1,338 @@
+#include "qcom-ipq8065-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "ZyXEL NBG6817";
+ compatible = "zyxel,nbg6817", "qcom,ipq8065";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+ sdcc1 = &sdcc1;
+ };
+
+ chosen {
+ bootargs = "rootfstype=squashfs noinitrd
block2mtd.block2mtd=/dev/mmcblk0p5,65536,ubi,5 ubi.mtd=ubi";
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
+ pinctrl-names = "default";
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ clk {
+ pins = "gpio1";
+ input-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29",
"gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59",
"gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ tx {
+ pins = "gpio27", "gpio28", "gpio29",
"gpio30", "gpio31", "gpio32" ;
+ input-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+
+ cs {
+ pins = "gpio20";
+ drive-strength = <12>;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ flash: m25p80@0 {
+ compatible = "s25fl512s";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <51200000>;
+ reg = <0>;
+
+ linux,part-probe = "qcom-smem";
+ };
+ };
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
+ 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
+ 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
+ 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
+ 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
+ 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
+ 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
+ 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
+ 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
+ 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
+ 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
+ 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
+ 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
+ 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ qca,ar8327-initvals = <
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x0000c 0x80 /* PAD6_MODE */
+ >;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <0>;
+ qcom,rgmii_delay = <1>;
+ qcom,phy_mii_type = <0>;
+ qcom,emulation = <0>;
+ qcom,irq = <255>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>; /* none */
+ qcom,poll_required = <0>; /* no polling */
+ qcom,rgmii_delay = <0>;
+ qcom,phy_mii_type = <1>;
+ qcom,emulation = <0>;
+ qcom,irq = <258>;
+ mdiobus = <&mdio0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ rpm@108000 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "default";
+ };
+
+ amba {
+ sdcc1: sdcc@12400000 {
+ status = "okay";
+ dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+ dma-names = "tx", "rx";
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 1>;
+ linux,code = <KEY_WLAN>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 1>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 1>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ internet {
+ label = "nbg6817:white:internet";
+ gpios = <&qcom_pinmux 64 0>;
+ };
+
+ power {
+ label = "nbg6817:white:power";
+ gpios = <&qcom_pinmux 9 0>;
+ default-state = "on";
+ };
+
+ wifi {
+ label = "nbg6817:white:wifi";
+ gpios = <&qcom_pinmux 33 0>;
+ };
+
+ wifi5g {
+ label = "nbg6817:white:wifi5g";
+ gpios = <&qcom_pinmux 26 0>;
+ };
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ usb0_status {
+ gpio-export,name = "usb0";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 15 0>;
+ };
+
+ usb1_status {
+ gpio-export,name = "usb1";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 16 0>;
+ };
+ usb1_power {
+ gpio-export,name = "usb1_power";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 14 0>;
+ };
+ usb2_power {
+ gpio-export,name = "usb2_power";
+ gpio-export,output = <1>;
+ gpios = <&qcom_pinmux 17 0>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
diff --git a/target/linux/ipq806x/image/Makefile
b/target/linux/ipq806x/image/Makefile
index 7703a62..4f9a87f 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -61,6 +61,18 @@ define Device/UbiFit
IMAGE/nand-sysupgrade.tar := sysupgrade-tar
endef
+define Device/ZyXELImage
+ PROFILES += $$(DEVICE_NAME)
+ FILESYSTEMS := squashfs
+ KERNEL_SUFFIX := -uImage
+ KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$(KERNEL_SIZE)
+ KERNEL_NAME := zImage
+ IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
+ IMAGE/sysupgrade.tar = sysupgrade-tar
+ IMAGE/mmcblk0p5-rootfs.bin := append-ubi
+ IMAGE/mmcblk0p4-kernel.bin := append-kernel
+endef
+
define Device/DniImage
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
@@ -200,6 +212,18 @@ define Device/R7800
DEVICE_PACKAGES := ath10k-firmware-qca9984
endef
-TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2
R7800
+define Device/NBG6817
+ DEVICE_DTS := qcom-ipq8065-nbg6817
+ KERNEL_SIZE := 4194304
+ BLOCKSIZE := 64k
+ PAGESIZE := 128
+ SUBPAGESIZE := 64
+ BOARD_NAME := nbg6817
+ DEVICE_TITLE := ZyXEL NBG6817
+ DEVICE_PACKAGES := ath10k-firmware-qca9984 kmod-fs-ext4
+ $(call Device/ZyXELImage)
+endef
+
+TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2
R7800 NBG6817
$(eval $(call BuildImage))
diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch
b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
index 85f2534..922dcfc 100644
--- a/target/linux/ipq806x/patches-4.4/800-devicetree.patch
+++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
@@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <j...@openwrt.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -506,7 +506,13 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -506,7 +506,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
qcom-ipq8064-ap148.dtb \
@@ -23,6 +23,7 @@ Signed-off-by: Jonas Gorski <j...@openwrt.org>
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7500v2.dtb \
+ qcom-ipq8065-r7800.dtb \
++ qcom-ipq8065-nbg6817.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
qcom-msm8974-sony-xperia-honami.dtb
diff --git a/target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch
b/target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch
new file mode 100644
index 0000000..45533e1
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch
@@ -0,0 +1,10 @@
+--- a/drivers/mtd/spi-nor/spi-nor.c 2016-10-09 00:34:19.206155838 +0200
++++ b/drivers/mtd/spi-nor/spi-nor.c 2016-10-09 00:37:11.048495602 +0200
+@@ -721,6 +721,7 @@ static const struct flash_info spi_nor_i
+ { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l3255e", INFO(0xc29e16, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
++ { "mx25u3235f", INFO(0xc22536, 0, 64 * 1024, 64, 0) },
+ { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
+ { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+ { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
--
2.1.4
_______________________________________________
Lede-dev mailing list
Lede-dev@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev
