Hello everyone,

Recently I update my lede repo to HEAD r1659 and found two problems in the firmware for clearfog pro board.

The first problem is about random. I got message below:

[    1.455149] init: Console is alive
[    1.458621] init: - watchdog -
[    1.662992] init: - preinit -
[ 1.765184] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available) [ 1.785144] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available) [ 1.801371] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available) [ 1.821036] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available) [ 1.836021] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[    1.852425] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 3.851416] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    3.859279] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    4.901827] mount_root: mounting /dev/root
[ 4.906144] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
[    4.918122] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    4.927956] urandom-seed: Seed file not found (/etc/urandom.seed)
[    4.957518] procd: - early -
[    4.960430] procd: - watchdog -
[    5.541489] procd: - ubus -
[ 5.598030] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available) [ 5.607015] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available) [ 5.615933] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available) [ 5.624909] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available) [ 5.633824] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    5.642880] procd: - init -
Please press Enter to activate this console.

Should I enable other packages ?

The other problem is that my QCA9880 WiFi cards can not work any more. Neither ath10k nor ath10k-ct driver can not work properly and give me almost the same message:

[ 6.217867] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[    6.228604] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.240597] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed [ 6.249693] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[    6.260083] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.269688] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed [ 6.278408] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[    6.288971] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.298511] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed [ 6.311374] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[    6.322114] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.331684] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed [ 6.340715] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-5.bin': -11 [ 6.350694] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[    6.361426] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.371006] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed [ 6.380047] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-4.bin': -11 [ 6.390029] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[    6.400756] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.410195] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed [ 6.419249] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-3.bin': -11 [ 6.442274] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 [ 6.451542] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0 [ 6.461013] ath10k_pci 0000:01:00.0: firmware ver 10.1.467-ct-_fW-016-0c89552 api 2 features wmi-10.x,has-wmi-mgmt-tx,txstatus-noac5 [ 6.503048] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[    6.513516] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 6.523298] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 6.534482] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[    7.798787] device eth0 entered promiscuous mode
[    7.804312] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[    7.818207] device eth1 entered promiscuous mode
[    7.822957] br-lan: port 2(eth1) entered forwarding state
[    7.828393] br-lan: port 2(eth1) entered forwarding state
[    7.833871] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[    7.847342] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 8.381410] ath10k_pci 0000:01:00.0: failed to receive control response completion, polling..
[    8.801423] br-lan: port 2(eth1) entered disabled state
[    9.381405] ath10k_pci 0000:01:00.0: Service connect timeout
[    9.387081] ath10k_pci 0000:01:00.0: failed to connect htt (-110)
[    9.472285] ath10k_pci 0000:01:00.0: could not init core (-110)
[    9.478259] ath10k_pci 0000:01:00.0: could not probe fw (-110)
[ 9.791414] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

Can anyone give me some advices ?

In the attachment you can find the whole boot message.

Regards,

Xue Liu

U-Boot SPL 2016.03 (Sep 25 2016 - 21:26:42)
High speed PHY - Version: 2.0
Detected Device ID 6828
board SerDes lanes topology details:
 | Lane #  | Speed |  Type       |
 --------------------------------
 |   0    |  3   |  SATA0       |
 |   1    |  0   |  SGMII1      |
 |   2    |  5   |  PCIe1       |
 |   3    |  5   |  USB3 HOST1  |
 |   4    |  5   |  PCIe2       |
 |   5    |  0   |  SGMII2      |
 --------------------------------
PCIe, Idx 1: detected no link
PCIe, Idx 2: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.29.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Trying to boot from MMC


U-Boot 2016.03 (Sep 25 2016 - 21:26:42 +0000)

SoC:   MV88F6828-A0 at 1600 MHz
I2C:   ready
DRAM:  1 GiB (800 MHz, ECC not enabled)
MMC:   mv_sdh: 0
*** Warning - bad CRC, using default environment

Model: SolidRun Clearfog A1
Board: SolidRun ClearFog
Net:   
Warning: ethernet@30000 (eth2) using random MAC address - 36:c7:49:3e:11:ce
eth2: ethernet@30000
Warning: ethernet@34000 (eth3) using random MAC address - 6e:3a:1c:22:aa:5f
, eth3: ethernet@34000
Warning: ethernet@70000 (eth1) using random MAC address - 46:33:f0:17:f7:83
, eth1: ethernet@70000
Hit any key to stop autoboot:  0 
reading boot.scr
327 bytes read in 9 ms (35.2 KiB/s)
Running bootscript from mmc ...
## Executing script at 01000000
reading zImage
2290768 bytes read in 113 ms (19.3 MiB/s)
reading armada-388-clearfog.dtb
18588 bytes read in 18 ms (1007.8 KiB/s)
Kernel image @ 0x2000000 [ 0x000000 - 0x22f450 ]
## Flattened Device Tree blob at 05f00000
   Booting using the fdt blob at 0x5f00000
   Loading Device Tree to 07a0a000, end 07a1189b ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.21 (l...@xue.liu@dks-koeln.de) (gcc version 5.4.0 (LEDE GCC 5.4.0 r1659) ) #0 SMP Sun Sep 25 21:26:42 26
[    0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: SolidRun Clearfog A1
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 12 pages/cpu @ef7ce000 s17984 r8192 d22976 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260608
[    0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk0p2 rootfstype=squashfs rootwait overlay=/dev/mmcblk0p3
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1032340K/1048576K available (4629K kernel code, 183K rwdata, 1628K rodata, 268K init, 296K bss, 16236K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06247ec   (6258 kB)
[    0.000000]       .init : 0xc0625000 - 0xc0668000   ( 268 kB)
[    0.000000]       .data : 0xc0668000 - 0xc0695c74   ( 184 kB)
[    0.000000]        .bss : 0xc0695c74 - 0xc06e006c   ( 297 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 D prefetch enabled, offset 1 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[    0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[    0.000000] Switching to timer-based delay loop, resolution 40ns
[    0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[    0.000009] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[    0.000106] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.000114] pid_max: default: 32768 minimum: 301
[    0.000152] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000156] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000348] CPU: Testing write buffer coherency: ok
[    0.000449] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.000474] Setting up static identity map for 0x8280 - 0x82d8
[    0.000560] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
[    0.000646] mvebu-pmsu: Initializing Power Management Service Unit
[    0.001049] Booting CPU 1
[    0.001221] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.001249] Brought up 2 CPUs
[    0.001255] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[    0.001258] CPU: All CPU(s) started in SVC mode.
[    0.003110] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.003188] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.003230] pinctrl core: initialized pinctrl subsystem
[    0.003548] NET: Registered protocol family 16
[    0.004035] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.029927] cpuidle: using governor ladder
[    0.032604] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[    0.032613] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[    0.060672] SCSI subsystem initialized
[    0.060868] usbcore: registered new interface driver usbfs
[    0.060895] usbcore: registered new interface driver hub
[    0.060919] usbcore: registered new device driver usb
[    0.061406] clocksource: Switched to clocksource armada_370_xp_clocksource
[    0.061844] NET: Registered protocol family 2
[    0.062063] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.062106] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.062166] TCP: Hash tables configured (established 8192 bind 8192)
[    0.062199] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.062221] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.062303] NET: Registered protocol family 1
[    0.063443] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.063491] Crashlog allocated RAM at address 0x3f00000
[    0.066081] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.066090] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.066982] bounce: pool size: 64 pages
[    0.066991] io scheduler noop registered
[    0.066997] io scheduler deadline registered (default)
[    0.067393] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[    0.067702] irq: Cannot allocate irq_descs @ IRQ50, assuming pre-allocated
[    0.067841] irq: Cannot allocate irq_descs @ IRQ82, assuming pre-allocated
[    0.068096] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.101853] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    0.101938] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.141829] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    0.141971] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.142261] console [ttyS0] disabled
[    0.162328] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 15625000) is a 16550A
[    0.727907] console [ttyS0] enabled
[    0.751600] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 15625000) is a 16550A
[    0.762690] loop: module loaded
[    0.766093] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    0.775182] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs 
[    0.784572] scsi host0: ahci-mvebu
[    0.788126] scsi host1: ahci-mvebu
[    0.791630] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 45
[    0.799565] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 45
[    0.807608] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    0.816686] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs 
[    0.826139] scsi host2: ahci-mvebu
[    0.829694] scsi host3: ahci-mvebu
[    0.833198] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 46
[    0.841133] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 46
[    0.850100] libphy: Fixed MDIO Bus: probed
[    0.854329] libphy: orion_mdio_bus: probed
[    0.859598] mvneta f1030000.ethernet eth0: Using random mac address b6:50:74:e5:c8:4d
[    0.868286] mvneta f1034000.ethernet eth1: Using random mac address 36:da:a9:6e:7b:7b
[    0.876933] mvneta f1070000.ethernet eth2: Using random mac address 1a:e8:84:12:7d:be
[    0.884844] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.891388] ehci-pci: EHCI PCI platform driver
[    0.895874] ehci-platform: EHCI generic platform driver
[    0.901199] ehci-orion: EHCI orion driver
[    0.905294] orion-ehci f1058000.usb: EHCI Host Controller
[    0.910714] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    0.918364] orion-ehci f1058000.usb: irq 40, io mem 0xf1058000
[    0.941422] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    0.947597] hub 1-0:1.0: USB hub found
[    0.951366] hub 1-0:1.0: 1 port detected
[    0.955596] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    0.960929] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    0.968529] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    0.977097] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
[    0.983073] hub 2-0:1.0: USB hub found
[    0.986842] hub 2-0:1.0: 1 port detected
[    0.990851] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    0.996188] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[    1.003723] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.012030] hub 3-0:1.0: USB hub found
[    1.015798] hub 3-0:1.0: 1 port detected
[    1.019846] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    1.025185] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    1.032774] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    1.041331] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
[    1.047324] hub 4-0:1.0: USB hub found
[    1.051092] hub 4-0:1.0: 1 port detected
[    1.055129] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    1.060457] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[    1.067989] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.076298] hub 5-0:1.0: USB hub found
[    1.080066] hub 5-0:1.0: 1 port detected
[    1.084196] usbcore: registered new interface driver usb-storage
[    1.090365] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[    1.098009] i2c /dev entries driver
[    1.112362] orion_wdt: Initial timeout 171 sec
[    1.116968] sdhci: Secure Digital Host Controller Interface driver
[    1.123169] sdhci: Copyright(c) Pierre Ossman
[    1.127694] sdhci-pxav3 f10d8000.sdhci: Got CD GPIO
[    1.132628] sdhci-pxav3 f10d8000.sdhci: No vmmc regulator found
[    1.138561] sdhci-pxav3 f10d8000.sdhci: No vqmmc regulator found
[    1.151422] ata1: SATA link down (SStatus 0 SControl 300)
[    1.156851] ata2: SATA link down (SStatus 0 SControl 300)
[    1.181419] ata4: SATA link down (SStatus 0 SControl 300)
[    1.186842] ata3: SATA link down (SStatus 0 SControl 300)
[    1.201452] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[    1.208962] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.215445] marvell-cesa f1090000.crypto: CESA device successfully registered
[    1.223138] NET: Registered protocol family 10
[    1.229209] NET: Registered protocol family 17
[    1.233694] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you n.
[    1.246350] 8021q: 802.1Q VLAN Support v1.8
[    1.250596] Registering SWP/SWPB emulation handler
[    1.256160] armada38x-rtc f10a3800.rtc: setting system clock to 2106-02-07 06:28:14 UTC (4294967294)
[    1.261051] mmc0: new high speed SDHC card at address 1234
[    1.261253] mmcblk0: mmc0:1234 SA04G 3.68 GiB 
[    1.262123]  mmcblk0: p1 p2 p3
[    1.281390] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.290935] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.327782] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    1.335302] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.342244] Freeing unused kernel memory: 268K (c0625000 - c0668000)
[    1.455149] init: Console is alive
[    1.458621] init: - watchdog -
[    1.662992] init: - preinit -
[    1.765184] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[    1.785144] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[    1.801371] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[    1.821036] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[    1.836021] random: jshn: uninitialized urandom read (4 bytes read, 7 bits of entropy available)
[    1.852425] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    3.851416] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    3.859279] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    4.901827] mount_root: mounting /dev/root
[    4.906144] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
[    4.918122] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    4.927956] urandom-seed: Seed file not found (/etc/urandom.seed)
[    4.957518] procd: - early -
[    4.960430] procd: - watchdog -
[    5.541489] procd: - ubus -
[    5.598030] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    5.607015] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    5.615933] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    5.624909] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    5.633824] random: ubusd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    5.642880] procd: - init -
Please press Enter to activate this console.
[    5.715702] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    5.724433] Loading modules backported from Linux version wt-2016-06-20-0-gbc17424
[    5.732039] Backport generated by backports.git backports-20160216-7-g5735958
[    5.776334] GPIO line 496 (pcie1.0-clkreq) hogged as input
[    5.782468] GPIO line 499 (pcie1.0-w-disable) hogged as output/low
[    5.788961] GPIO line 500 (pcie2.0-clkreq) hogged as input
[    5.795083] GPIO line 503 (pcie2.0-w-disable) hogged as output/low
[    5.801578] GPIO line 501 (usb3-current-limit) hogged as input
[    5.808033] GPIO line 502 (usb3-power) hogged as output/high
[    5.814320] GPIO line 507 (m.2 devslp) hogged as output/low
[    5.820203] GPIO line 508 (sfp-los) hogged as input
[    5.825396] GPIO line 509 (sfp-tx-fault) hogged as input
[    5.831328] GPIO line 510 (sfp-tx-disable) hogged as output/low
[    5.837565] GPIO line 511 (sfp-mod-def0) hogged as input
[    5.842941] pca953x 0-0020: interrupt support not compiled in
[    5.848881] mvebu-pcie soc:pcie-controller: /soc/pcie-controller/pcie@2,0: reset gpio is active low
[    5.858594] mvebu-pcie soc:pcie-controller: /soc/pcie-controller/pcie@3,0: reset gpio is active low
[    5.885544] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.892657] nf_conntrack version 0.5.0 (16134 buckets, 64536 max)
[    5.921540] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[    5.928436] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    5.934728] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    5.941623] pci_bus 0000:00: root bus resource [bus 00-ff]
[    5.947337] PCI: bus0: Fast back to back transfers disabled
[    5.952929] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    5.960953] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    5.969230] PCI: bus1: Fast back to back transfers disabled
[    5.974880] PCI: bus2: Fast back to back transfers enabled
[    5.980422] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[    5.987239] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit]
[    5.994577] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0200000-0xe020ffff pref]
[    6.001820] pci 0000:00:02.0: PCI bridge to [bus 01]
[    6.006797] pci 0000:00:02.0:   bridge window [mem 0xe0000000-0xe02fffff]
[    6.013606] pci 0000:00:03.0: PCI bridge to [bus 02]
[    6.018647] ath10k driver, optimized for CT firmware, probing pci.
[    6.025194] pci 0000:00:02.0: enabling device (0140 -> 0142)
[    6.030879] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[    6.037358] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[    6.084946] xt_time: kernel timezone is -0000
[    6.091333] PPP generic driver version 2.4.2
[    6.096000] NET: Registered protocol family 24
[    6.217867] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[    6.228604] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.240597] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[    6.249693] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[    6.260083] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.269688] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[    6.278408] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2
[    6.288971] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.298511] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[    6.311374] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[    6.322114] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.331684] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[    6.340715] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-5.bin': -11
[    6.350694] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[    6.361426] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.371006] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[    6.380047] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-4.bin': -11
[    6.390029] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[    6.400756] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.410195] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[    6.419249] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-3.bin': -11
[    6.442274] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[    6.451542] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[    6.461013] ath10k_pci 0000:01:00.0: firmware ver 10.1.467-ct-_fW-016-0c89552 api 2 features wmi-10.x,has-wmi-mgmt-tx,txstatus-noac5
[    6.503048] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[    6.513516] ath10k_pci 0000:01:00.0: Falling back to user helper
[    6.523298] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[    6.534482] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[    7.798787] device eth0 entered promiscuous mode
[    7.804312] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[    7.818207] device eth1 entered promiscuous mode
[    7.822957] br-lan: port 2(eth1) entered forwarding state
[    7.828393] br-lan: port 2(eth1) entered forwarding state
[    7.833871] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[    7.847342] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[    8.381410] ath10k_pci 0000:01:00.0: failed to receive control response completion, polling..
[    8.801423] br-lan: port 2(eth1) entered disabled state
[    9.381405] ath10k_pci 0000:01:00.0: Service connect timeout
[    9.387081] ath10k_pci 0000:01:00.0: failed to connect htt (-110)
[    9.472285] ath10k_pci 0000:01:00.0: could not init core (-110)
[    9.478259] ath10k_pci 0000:01:00.0: could not probe fw (-110)
[    9.791414] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    9.799276] br-lan: port 1(eth0) entered forwarding state
[    9.804705] br-lan: port 1(eth0) entered forwarding state
[    9.811421] mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[    9.819275] br-lan: port 2(eth1) entered forwarding state
[    9.824700] br-lan: port 2(eth1) entered forwarding state
[   11.801400] br-lan: port 1(eth0) entered forwarding state
[   11.821399] br-lan: port 2(eth1) entered forwarding state
[   12.841819] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[   12.849677] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
_______________________________________________
Lede-dev mailing list
Lede-dev@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev

Reply via email to