Hi Daniel,
please see the attached files.
Thanks
Dennis
Gesendet: Freitag, 23. September 2016 um 21:49 Uhr
Von: "Daniel Golle" <dan...@makrotopia.org>
An: "Dennis Schneck" <dennisschn...@web.de>
Cc: lede-dev@lists.infradead.org
Betreff: Re: [LEDE-DEV] o2 box 6431 / VGV7510KW22 - WLAN did not work
On Fri, Sep 23, 2016 at 08:14:03PM +0200, Dennis Schneck wrote:
>
>
> Hello,
> i use the o2 box 6431 / VGV7510KW22 with LEDE r1640.
> But the wireless did not work.
>
> The Kernel Module: rt2800.... is loaded
> but there is no wlan interface.
weird. please post your kernel log and the output of
cat /proc/bus/pci/devices
it should actually work and i got a similar device here
working well with rt2800pci... maybe the eeprom is missing or we
haven't found a method to extract it from the original fw...?
>
> How to fix this ?
>
> Thanks
> Dennis
>
> _______________________________________________
> Lede-dev mailing list
> Lede-dev@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/lede-dev
root@lede:~# cat /proc/bus/pci/devices
0070 18143592 1e 18000000 0
0 0 0
0 0 10001
0 0 0 0
0 0
root@lede:~# dmesg
[ 0.000000] Linux version 4.4.21 (buildbot@builds) (gcc version 5.4.0 (LEDE
GCC 5.4.0 r1422) ) #0 Wed Sep 21 12:20:20 2016
[ 0.000000] SoC: xRX200 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is VGV7510KW22 - o2 Box 6431
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 805144b0, node_mem_map
810089e0
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00075940
[ 0.000000] Readback ErrCtl register=00075940
[ 0.000000] Memory: 58136K/65536K available (3901K kernel code, 170K rwdata,
1252K rodata, 1188K init, 212K bss, 7400K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 7645041786 ns
[ 0.000010] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every
8589934590ns
[ 0.007854] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.042317] pid_max: default: 32768 minimum: 301
[ 0.047155] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.053726] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.066783] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 7645041785100000 ns
[ 0.076601] pinctrl core: initialized pinctrl subsystem
[ 0.083088] NET: Registered protocol family 16
[ 0.092239] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.097774] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7,
channels: 28
[ 0.207853] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.222964] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.228608] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.233863] IO 0x000000001ae00000..0x000000001affffff
[ 0.254700] usbcore: registered new interface driver usbfs
[ 0.260190] usbcore: registered new interface driver hub
[ 0.265549] usbcore: registered new device driver usb
[ 0.271062] PCI host bridge to bus 0000:00
[ 0.275058] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.281966] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.288911] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.295767] pci_bus 0000:00: No busn resource found for root bus, will use
[bus 00-ff]
[ 0.303815] pci 0000:00:0e.0: [1814:3592] type 00 class 0x028000
[ 0.303871] pci 0000:00:0e.0: reg 0x10: [mem 0xffff0000-0xffffffff]
[ 0.303970] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold
[ 0.304270] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.304311] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.312139] clocksource: Switched to clocksource MIPS
[ 0.318735] NET: Registered protocol family 2
[ 0.324041] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.330935] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.337311] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.343826] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.349663] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.356284] NET: Registered protocol family 1
[ 0.360623] PCI: CLS 0 bytes, default 32
[ 0.367534] gptu: totally 6 16-bit timers/counters
[ 0.372374] gptu: misc_register on minor 63
[ 0.376473] gptu: succeeded to request irq 126
[ 0.380960] gptu: succeeded to request irq 127
[ 0.385473] gptu: succeeded to request irq 128
[ 0.389987] gptu: succeeded to request irq 129
[ 0.394501] gptu: succeeded to request irq 130
[ 0.399014] gptu: succeeded to request irq 131
[ 0.403881] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[ 0.410272] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy22f_a2x.bin
[ 0.417569] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3980000
[ 0.423894] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3980000
[ 0.531429] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.537531] Crashlog allocated RAM at address 0x3f00000
[ 0.563437] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.569188] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.583123] io scheduler noop registered
[ 0.586946] io scheduler deadline registered (default)
[ 0.592882] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112,
base_baud = 0) is a lantiq,asc
[ 0.601780] console [ttyLTQ0] enabled
[ 0.609105] bootconsole [early0] disabled
[ 0.618170] lantiq nor flash device: 01000000 at 10000000
[ 0.622289] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer
ID 0x0000c2 Chip ID 0x00227e
[ 0.631729] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.636865] Amd/Fujitsu Extended Query version 1.3.
[ 0.641897] number of CFI chips: 1
[ 0.645328] 4 ofpart partitions found on MTD device ltq_nor
[ 0.650861] Creating 4 MTD partitions on "ltq_nor":
[ 0.655740] 0x000000fe0000-0x000001000000 : "board_config"
[ 0.664811] 0x000000000000-0x000000060000 : "uboot"
[ 0.670393] 0x000000060000-0x000000080000 : "uboot-env"
[ 0.676372] 0x000000080000-0x000000fe0000 : "firmware"
[ 0.692578] 2 uimage-fw partitions found on MTD device firmware
[ 0.697110] 0x000000080000-0x00000022665f : "kernel"
[ 0.703797] 0x00000022665f-0x000000fe0000 : "rootfs"
[ 0.709532] mtd: device 5 (rootfs) set to be root filesystem
[ 0.713833] 1 squashfs-split partitions found on MTD device rootfs
[ 0.719950] 0x000000500000-0x000000fe0000 : "rootfs_data"
[ 0.830841] libphy: lantiq,xrx200-mdio: probed
[ 0.904843] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11,
irq=-1)
[ 0.972831] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12,
irq=-1)
[ 1.040830] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13,
irq=-1)
[ 1.108831] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14,
irq=-1)
[ 1.180312] eth1: attached PHY [ICPlus IP101A/G] (phy_addr=0:01, irq=-1)
[ 1.187183] ltq-cputemp cputemp@0: Current CPU die temperature: 96 °C
[ 1.192547] wdt 1f8803f0.watchdog: Init done
[ 1.200052] NET: Registered protocol family 10
[ 1.210049] NET: Registered protocol family 17
[ 1.213210] bridge: automatic filtering via arp/ip/ip6tables has been
deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.225721] 8021q: 802.1Q VLAN Support v1.8
[ 1.240695] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.250297] Freeing unused kernel memory: 1188K (80537000 - 80660000)
[ 2.362913] init: Console is alive
[ 2.365209] init: - watchdog -
[ 3.172727] eth0: port 3 got link
[ 3.629892] dwc2 1e101000.ifxhcd: requested GPIO 509
[ 3.633496] dwc2 1e101000.ifxhcd: Configuration mismatch. Forcing host mode
[ 4.496337] dwc2 1e101000.ifxhcd: DWC OTG Controller
[ 4.499931] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus
number 1
[ 4.507243] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[ 4.512771] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA
mode -
[ 4.520216] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[ 4.527775] hub 1-0:1.0: USB hub found
[ 4.530656] hub 1-0:1.0: 1 port detected
[ 4.536943] init: - preinit -
[ 5.281436] random: procd: uninitialized urandom read (4 bytes read, 22 bits
of entropy available)
[ 8.622292] jffs2: notice: (393) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0
dead, 0 orphan) found.
[ 8.639259] mount_root: switching to jffs2 overlay
[ 8.651749] urandom-seed: Seeding with /etc/urandom.seed
[ 8.826043] procd: - early -
[ 8.827653] procd: - watchdog -
[ 9.172179] eth0: port 3 lost link
[ 9.483734] procd: - ubus -
[ 9.496908] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.536765] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.544913] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.553399] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.563302] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.571323] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.580581] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.589558] random: ubusd: uninitialized urandom read (4 bytes read, 39 bits
of entropy available)
[ 9.598801] procd: - init -
[ 9.991373] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 10.003774] NET: Registered protocol family 8
[ 10.006740] NET: Registered protocol family 20
[ 10.018456] PPP generic driver version 2.4.2
[ 10.029628] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.058364] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015
Lantiq Beteiligungs-GmbH & Co. KG
[ 10.058364]
[ 10.058364] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[ 10.083030]
[ 10.083030] Predefined debug level: 3
[ 10.095496] Loading modules backported from Linux version
wt-2016-06-20-0-gbc17424
[ 10.101681] Backport generated by backports.git backports-20160216-7-g5735958
[ 10.113947] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.126082] Infineon Technologies DEU driver version 2.0.0
[ 10.132188] IFX DEU DES initialized (multiblock).
[ 10.136522] IFX DEU AES initialized (multiblock).
[ 10.140612] IFX DEU ARC4 initialized (multiblock).
[ 10.145232] IFX DEU SHA1 initialized.
[ 10.148830] IFX DEU MD5 initialized.
[ 10.152492] IFX DEU SHA1_HMAC initialized.
[ 10.156493] IFX DEU MD5_HMAC initialized.
[ 10.168502] nf_conntrack version 0.5.0 (926 buckets, 3704 max)
[ 10.198280] NET: Registered protocol family 24
[ 10.228504] xt_time: kernel timezone is -0000
[ 10.330250] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 10.334709] rt2800pci 0000:00:0e.0: failed to load eeprom property
[ 10.340701] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading
EEPROM data from 'RT3062.eeprom'.
[ 10.350649] rt2800pci 0000:00:0e.0: Direct firmware load for RT3062.eeprom
failed with error -2
[ 10.359155] rt2800pci 0000:00:0e.0: Falling back to user helper
[ 10.597927] firmware RT3062.eeprom: firmware_loading_store: map pages failed
[ 10.603810] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to
request EEPROM.
[ 10.612118] rt2800pci: probe of 0000:00:0e.0 failed with error -11
[ 12.687465] random: jshn: uninitialized urandom read (4 bytes read, 52 bits
of entropy available)
[ 17.176693] PTM 1.0.27 PTM (E1) firmware version 0.30
[ 17.180613] ifxmips_ptm: PTM init succeed
[ 22.128236] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.147146] device eth0.1 entered promiscuous mode
[ 22.150562] device eth0 entered promiscuous mode
[ 22.169785] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 22.239503] IPv6: ADDRCONF(NETDEV_UP): ptm0: link is not ready
[ 22.256388] eth0: port 3 got link
[ 22.258460] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.284308] br-lan: port 1(eth0.1) entered forwarding state
[ 22.288565] br-lan: port 1(eth0.1) entered forwarding state
[ 22.396886] IPv6: ADDRCONF(NETDEV_UP): ptm0.232: link is not ready
[ 22.401769] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.419524] IPv6: ADDRCONF(NETDEV_UP): ptm0.132: link is not ready
[ 24.292156] br-lan: port 1(eth0.1) entered forwarding state
[ 31.468199] random: nonblocking pool is initialized
[ 55.267648] enter showtime
[ 55.269145] IPv6: ADDRCONF(NETDEV_CHANGE): ptm0: link becomes ready
[ 55.280000] enter showtime
[ 55.283485] IPv6: ADDRCONF(NETDEV_CHANGE): ptm0.132: link becomes ready
[ 55.289241] IPv6: ADDRCONF(NETDEV_CHANGE): ptm0.232: link becomes ready
_______________________________________________
Lede-dev mailing list
Lede-dev@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev
