On Fri, Nov 07, 2014 at 03:58:19PM -0800, Andy Lutomirski wrote:
> We used to optimize rescheduling and audit on syscall exit. Now that
> the full slow path is reasonably fast, remove these optimizations.
>
> This adds something like 10ns to the previously optimized paths on my
> computer, presumably due mostly to SAVE_REST / RESTORE_REST.
>
> I think that we should eventually replace both the syscall and
> non-paranoid interrupt exit slow paths with a pair of C functions
> along the lines of the syscall entry hooks.
>
> Signed-off-by: Andy Lutomirski <l...@amacapital.net>
> ---
> arch/x86/kernel/entry_64.S | 52
> +++++-----------------------------------------
> 1 file changed, 5 insertions(+), 47 deletions(-)
>
> diff --git a/arch/x86/kernel/entry_64.S b/arch/x86/kernel/entry_64.S
> index a5afdf0f7fa4..222dc5c45ac3 100644
> --- a/arch/x86/kernel/entry_64.S
> +++ b/arch/x86/kernel/entry_64.S
> @@ -427,15 +427,12 @@ system_call_fastpath:
> * Has incomplete stack frame and undefined top of stack.
> */
> ret_from_sys_call:
> - movl $_TIF_ALLWORK_MASK,%edi
> - /* edi: flagmask */
> -sysret_check:
> + testl $_TIF_ALLWORK_MASK,TI_flags+THREAD_INFO(%rsp,RIP-ARGOFFSET)
> + jnz int_ret_from_sys_call_fixup /* Go the the slow path */
> +
> LOCKDEP_SYS_EXIT
> DISABLE_INTERRUPTS(CLBR_NONE)
> TRACE_IRQS_OFF
> - movl TI_flags+THREAD_INFO(%rsp,RIP-ARGOFFSET),%edx
> - andl %edi,%edx
> - jnz sysret_careful
> CFI_REMEMBER_STATE
> /*
> * sysretq will re-enable interrupts:
> @@ -449,49 +446,10 @@ sysret_check:
> USERGS_SYSRET64
>
> CFI_RESTORE_STATE
> - /* Handle reschedules */
> - /* edx: work, edi: workmask */
> -sysret_careful:
> - bt $TIF_NEED_RESCHED,%edx
> - jnc sysret_signal
> - TRACE_IRQS_ON
> - ENABLE_INTERRUPTS(CLBR_NONE)
> - pushq_cfi %rdi
> - SCHEDULE_USER
> - popq_cfi %rdi
> - jmp sysret_check
>
> - /* Handle a signal */
> -sysret_signal:
> - TRACE_IRQS_ON
> - ENABLE_INTERRUPTS(CLBR_NONE)
> -#ifdef CONFIG_AUDITSYSCALL
> - bt $TIF_SYSCALL_AUDIT,%edx
> - jc sysret_audit
> -#endif
> - /*
> - * We have a signal, or exit tracing or single-step.
> - * These all wind up with the iret return path anyway,
> - * so just join that path right now.
> - */
> +int_ret_from_sys_call_fixup:
> FIXUP_TOP_OF_STACK %r11, -ARGOFFSET
> - jmp int_check_syscall_exit_work
> -
> -#ifdef CONFIG_AUDITSYSCALL
> - /*
> - * Return fast path for syscall audit. Call __audit_syscall_exit()
> - * directly and then jump back to the fast path with TIF_SYSCALL_AUDIT
> - * masked off.
> - */
> -sysret_audit:
> - movq RAX-ARGOFFSET(%rsp),%rsi /* second arg, syscall return value */
> - cmpq $-MAX_ERRNO,%rsi /* is it < -MAX_ERRNO? */
> - setbe %al /* 1 if so, 0 if not */
> - movzbl %al,%edi /* zero-extend that into %edi */
> - call __audit_syscall_exit
> - movl $(_TIF_ALLWORK_MASK & ~_TIF_SYSCALL_AUDIT),%edi
> - jmp sysret_check
> -#endif /* CONFIG_AUDITSYSCALL */
> + jmp int_ret_from_sys_call
Ok, dumb question: what is replacing that audit functionality now?
Or are we remaining with the single path down syscall_trace_leave()?
AFAICT, the intention is to direct everything to int_ret_from_sys_call
after the syscall has been done so that paths can get simplified. Which
is a good thing, AFAICT.
Acked-by: Borislav Petkov <b...@suse.de>
--
Regards/Gruss,
Boris.
Sent from a fat crate under my desk. Formatting is fine.
--
--
To unsubscribe from this list: send the line "unsubscribe kvm" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
