On Fri, Jun 06, 2008 at 11:59:02PM +0800, Xu, Anthony wrote:
> In kvm-ia64, PCI devices use 48-pin virtual IOAPIC to deliver interrup.
>
>
> Signed-off-by: Anthony Xu < [EMAIL PROTECTED] >
>
> diff --git a/qemu/hw/piix_pci.c b/qemu/hw/piix_pci.c
> index 90cb3a6..797ece7 100644
> --- a/qemu/hw/piix_pci.c
> +++ b/qemu/hw/piix_pci.c
> @@ -28,6 +28,7 @@
>
> typedef uint32_t pci_addr_t;
> #include "pci_host.h"
> +#include "qemu-kvm.h"
>
> typedef PCIHostState I440FXState;
>
> @@ -51,6 +52,11 @@ static void piix3_set_irq(qemu_irq *pic, int irq_num,
> int level);
> static int pci_slot_get_pirq(PCIDevice *pci_dev, int irq_num)
> {
> int slot_addend;
> +#if defined(KVM_CAP_IRQCHIP) && defined(TARGET_IA64)
> + int dev;
> + dev = pci_dev->devfn >> 3;
> + return (((((dev) << 2) + ((dev) >> 3) + (irq_num)) & 31) + 16);
> +#endif
> slot_addend = (pci_dev->devfn >> 3) - 1;
> return (irq_num + slot_addend) & 3;
> }
You don't support -no-kvm-irqchip on IA64?
Also, cosmetically would be nicer to create a separate get_pirq function
for IA64.
> @@ -171,12 +177,18 @@ static int i440fx_load(QEMUFile* f, void *opaque,
> int version_id)
>
> PCIBus *i440fx_init(PCIDevice **pi440fx_state, qemu_irq *pic)
> {
> + int nirq;
> PCIBus *b;
> PCIDevice *d;
> I440FXState *s;
>
> +#if defined(KVM_CAP_IRQCHIP) && defined(TARGET_IA64)
> + nirq = 48;
> +#else
> + nirq = 4;
> +#endif
> s = qemu_mallocz(sizeof(I440FXState));
> - b = pci_register_bus(piix3_set_irq, pci_slot_get_pirq, pic, 0, 4);
> + b = pci_register_bus(piix3_set_irq, pci_slot_get_pirq, pic, 0,
> nirq);
> s->bus = b;
This should be dynamic if possible. Don't want another ifdef for when x86
routes through IOAPIC.
> register_ioport_write(0xcf8, 4, 4, i440fx_addr_writel, s);
> @@ -220,6 +232,11 @@ static void piix3_set_irq(qemu_irq *pic, int
> irq_num, int level)
> {
> int i, pic_irq, pic_level;
>
> +#if defined(KVM_CAP_IRQCHIP) && defined(TARGET_IA64)
> + if(kvm_enabled())
> + kvm_set_irq(irq_num, level);
> + return;
> +#endif
> pci_irq_levels[irq_num] = level;
Why the current hook into i8259_set_irq does not work for IA64?
I think this breaks interrupt sharing, because the logic to detect if
all devices sharing the line are low or high is in i8259_set_irq, and
you simply skip that.
--
To unsubscribe from this list: send the line "unsubscribe kvm" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
