Virgil Mine will be, I sprung for Stainless Steel.
Don ------------------------------------------------------------------------ VIRGIL N SALISBURY wrote: > They will not be corrosion resistant any more, Virg > > On Fri, 5 May 2006 18:01:58 -0500 "M & C" <aviato...@charter.net> writes: > > Why brother trying to reem holes that are hard to get to? If the > > bolts are a > > close fit just take the embry cloth to the bolts and reduce bolt > > diameters > > slightly. I would not think this would reduce the bolt strength > > enough to > > amount to anything. Stick the bolts in a drill press Just at the > > grip/thread > > point and let it spin while holding a strip of embry cloth thus > > reducing all > > sides of the bolts in an even pattern. > > Mike Turner > > Jackson Mo > > ----- Original Message ----- > > From: "D F Lively" <riksh...@interl.net> > > To: "KRNET" <kr...@mylist.net> > > Sent: Friday, May 05, 2006 5:09 PM > > Subject: Re: KR> Reamers > > > > > > > Bobby: > > > > > > Sounds good but I can not seem to find one intown to buy---- but > > I have > > > not tried any of the EAA guys here. It looks like the person that > > made > > > these used an under sized bit bicause I used a 3/8 " and a 7/64" > > bit in > > > wood and they were just right! Thanks for the suggestion I'll > > try a > > > chapter EAA member and see if he has one. > > > > > > Don > > > > > > ------------------------------------------------------------------------ > > > > > > bo...@hatconversions.com wrote: > > > > > >> Don, Use an adjustable hand reamer. It's lots quicker, and your > > holes > > >> will > > >> stay round.........Bobby > > >> > > >> > Virgil: > > >> > > > >> > I am back to the Dowel & Emory paper sice the WAF's are > > already > > >> insyalled > > >> > on > > >> > the closed up wing I can not even use a hand drill let alone a > > drill > > >> press > > >> > so > > >> > this will take a while. I already had the wings on with > > ordinary > > >> bolts so > > >> > I > > >> > know they fit that way but they only go on the 1st half of the > > grip > > >> of the > > >> > bolt at most. > > >> > > > >> > Thanks > > >> > > > >> > Don > > >> > > > >> > > > ------------------------------------------------------------------------ > > >> > > >> > > > >> > VIRGIL N SALISBURY wrote: > > >> > > > >> >> Drill the bolt holes undersized then ream. You do one > > at a > > >> time, > > >> >> KEEP > > >> >> the reamer square to the work. Put it in the drill press and > > hand > > >> turn. > > >> >> Lubricate > > >> >> well, Virg > > >> >> > > >> >> On Fri, 5 May 2006 23:00:49 +1000 "Chris Johnston" > > >> >> <chr...@ozdocs.net.au> > > >> >> writes: > > >> >> > I am on the scrounge for parts, I need some > > undercarriage > > >> >> > fittings, the Diehl ones for fitting to the spars, if anyone > > has > > >> an > > >> >> > old or disused set I would be interested, is the length of > > the > > >> kr2 > > >> >> > gear legs the same as the length of the kr2s, and can you > > make > > >> the > > >> >> > legs from Aluminium, failing all that, it might be safer > > just to > > >> buy > > >> >> > the complete Diehl gear set and be done with it, and yes, I > > have > > >> >> > been very bad in that I have not checked the archives on > > this. > > >> >> > I am also wanting wing attachment fittings, I would > > think it > > >> >> > would be pretty easy to make thses at home, send a cad file > > to > > >> the > > >> >> > CNC water jet guy and have them cut out, I am told they can > > do > > >> them > > >> >> > here to +/- 2 thou, will the bolt holes need reaming? and > > what s > > >> the > > >> >> > best way to do this, fit them in a jig and do them all in > > one or > > >> do > > >> >> > them individually????? Any advice greatly appreciated, and > > yes, > > >> >> > again, I have not checked the archives. > > >> >> > > > >> >> > > > >> >> > > > >> >> > > > >> >> > > > >> >> > Chris Johnston > > >> >> > > > >> >> > North Richmond > > >> >> > > > >> >> > Australia > > >> >> > _______________________________________ > > >> >> > Search the KRnet Archives at > > >> >> > http://www.maddyhome.com/krsrch/index.jsp > > >> >> > to UNsubscribe from KRnet, send a message to > > >> krnet-le...@mylist.net > > >> >> > please see other KRnet info at > > http://www.krnet.org/info.html > > >> >> > > > >> >> > > > >> >> > > >> >> Virgil N. Salisbury - AMSOIL > > >> >> www.lubedealer.com/salisbury > > >> >> Miami ,Fl > > >> >> > > >> >> _______________________________________ > > >> >> Search the KRnet Archives at > > >> http://www.maddyhome.com/krsrch/index.jsp > > >> >> to UNsubscribe from KRnet, send a message to > > krnet-le...@mylist.net > > >> > > >> >> please see other KRnet info at http://www.krnet.org/info.html > > >> > _______________________________________ > > >> > Search the KRnet Archives at > > >> http://www.maddyhome.com/krsrch/index.jsp > > >> > to UNsubscribe from KRnet, send a message to > > krnet-le...@mylist.net > > >> > please see other KRnet info at http://www.krnet.org/info.html > > >> > > > >> > > >> _______________________________________ > > >> Search the KRnet Archives at > > http://www.maddyhome.com/krsrch/index.jsp > > >> > > >> to UNsubscribe from KRnet, send a message to > > krnet-le...@mylist.net > > >> please see other KRnet info at http://www.krnet.org/info.html > > > _______________________________________ > > > Search the KRnet Archives at > > http://www.maddyhome.com/krsrch/index.jsp > > > to UNsubscribe from KRnet, send a message to > > krnet-le...@mylist.net > > > please see other KRnet info at http://www.krnet.org/info.html > > > > > > > _______________________________________ > > Search the KRnet Archives at > > http://www.maddyhome.com/krsrch/index.jsp > > to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net > > please see other KRnet info at http://www.krnet.org/info.html > > > > > > Virgil N. Salisbury - AMSOIL > www.lubedealer.com/salisbury > Miami ,Fl > > _______________________________________ > Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp > to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net > please see other KRnet info at http://www.krnet.org/info.html
