I finally had a chance to look at this patch and I have similar concerns. I thought I was pretty clear about *not* being comfortable with making assumptions about via zone connections and always using the assigned net code. I'm a bit concerned with the connection testing and it's decision to change a via's net code depending on which zone(s) that it intersects. I see this as an unacceptable risk for kicad to assume. I would rather put the responsibility in hands of the user and just have kicad complain when there is a drc issue.
Please configure your editor to clean up trailing white space and fix the other coding policy errors. Cheers, Wayne On 10/23/2016 10:44 PM, Strontium wrote: > Hello Heikki, > > Can you explain the logic you are using to determine the net of the vias > during DRC reconnect? It looks like you are only considering the top > and bottom layer, but stitching vias may be stitching internal layers? > > Steven > > > On 23/10/16 21:48, Heikki Pulkkinen wrote: >> Hi Wayne and all, >> >> About that my suggestion of Via Stitching. I do some tests and found >> that if DRC first fill zones and then do tests it does not break >> anything. if you forgot to Fill or Refill zoenes before running DRC. >> >> Regards >> >> Heikki >> >> >> On Fri, Oct 21, 2016 at 6:41 PM, Heikki Pulkkinen <hei6m...@gmail.com >> <mailto:hei6m...@gmail.com>> wrote: >> >> Hi Wayne, >> >> If you try this, I send the last full patch of that Via Stitching. >> Do not care other patches in mailing list, they are more or less >> incomplete. >> >> Regards >> >> Heikki >> >> On Tue, Oct 18, 2016 at 3:22 PM, Wayne Stambaugh >> <stambau...@gmail.com <mailto:stambau...@gmail.com>> wrote: >> >> I will look at when I get a chance. When that will be I >> cannot say for >> sure. I've just been really busy. I will try to get around >> to it this >> weekend. >> >> Cheers, >> >> Wayne >> >> On 10/17/2016 3:40 PM, Jakub Kozdon wrote: >> > Hi, it looks usable. >> > >> > Don't know if it is visible for all, but Wayne, what do you >> think about it? >> > >> > Jakub >> > >> > Dne 16.10.2016 v 19:23 Heikki Pulkkinen napsal(a): >> >> Hi, >> >> >> >> I add array feature to my Via Stitching. And an another >> slowly video >> >> to watch. >> >> https://youtu.be/28nfoZPg2bg >> >> >> >> Full fixed patch and array test patch. More work have to be >> done, but >> >> this was easy start. >> >> >> >> Regards >> >> >> >> Heikki >> >> >> >> On Thu, Oct 13, 2016 at 7:23 PM, Heikki Pulkkinen >> <hei6m...@gmail.com <mailto:hei6m...@gmail.com> >> >> <mailto:hei6m...@gmail.com <mailto:hei6m...@gmail.com>>> wrote: >> >> >> >> Hi, >> >> >> >> Here is demovideo about via stitching. It is slowly, >> because of >> >> slowly machine. I do some development too, so full patch is >> >> attached too. >> >> >> >> On Tue, Oct 11, 2016 at 5:49 PM, Marcos Chaparro >> >> <nitrous...@gmail.com <mailto:nitrous...@gmail.com> >> <mailto:nitrous...@gmail.com <mailto:nitrous...@gmail.com>>> >> wrote: >> >> >> >> Hi Heikki, >> >> is there any chance to make some screenshots or >> video about >> >> this? Some of us do compile kicad to get the latest and >> >> greatest but never applied a patch for a particular >> feature. >> >> >> >> Regards >> >> >> >> >> >> Marcos >> >> >> >> On Sat, Oct 8, 2016 at 7:04 AM, Heikki Pulkkinen >> >> <hei6m...@gmail.com <mailto:hei6m...@gmail.com> >> <mailto:hei6m...@gmail.com <mailto:hei6m...@gmail.com>>> wrote: >> >> >> >> Hi, >> >> >> >> Putting back that my via stitching tool to >> routing tool. >> >> It is better that way, I think. All via tools >> are in same >> >> place, and it adds vias to pours only from hotkeys. >> >> >> >> >> >> >> >> On Sun, Oct 2, 2016 at 12:28 PM, Heikki Pulkkinen >> >> <hei6m...@gmail.com <mailto:hei6m...@gmail.com> >> <mailto:hei6m...@gmail.com <mailto:hei6m...@gmail.com>>> wrote: >> >> >> >> Hi, >> >> >> >> Finally Via Stitching without tracks is at >> zone tool. >> >> I tested it little bit, but more tests are >> needed. >> >> This patch replace all other patches. Do >> not use them, >> >> use only this patch. I think this is worth >> of try. I >> >> am going to use it anyway, even if it do >> not get any >> >> acceptance. First patch is for Fedora >> users. It makes >> >> possible to build Kicad in Fedora release >> wxWidgets >> >> libs whitout building wxWidget from source. >> I do not >> >> know has anybody else that problem, but I had. >> >> >> >> >> >> Heikki >> >> >> >> On Tue, Sep 27, 2016 at 6:46 PM, Heikki >> Pulkkinen >> >> <hei6m...@gmail.com <mailto:hei6m...@gmail.com> >> <mailto:hei6m...@gmail.com <mailto:hei6m...@gmail.com>>> wrote: >> >> >> >> Hi >> >> >> >> And I really practice. I made >> improvement and >> >> forgot to copy all. So improvement is >> in these two >> >> patches. I hope this suggestion is >> accepted as a >> >> new feature. >> >> >> >> Heikki >> >> >> >> On Tue, Sep 27, 2016 at 2:31 PM, Heikki >> Pulkkinen >> >> <hei6m...@gmail.com >> <mailto:hei6m...@gmail.com> <mailto:hei6m...@gmail.com >> <mailto:hei6m...@gmail.com>>> >> >> wrote: >> >> >> >> Hi, >> >> >> >> As in practice, I made a patch >> file of my >> >> changes Not only diifs. It is >> SHIFT-ALT-V >> >> hotkey whitch make buried and blind >> vias, as >> >> it is in routing too. >> >> >> >> >> >> Heikki >> >> >> >> On Sun, Sep 25, 2016 at 2:25 PM, Heikki >> >> Pulkkinen <hei6m...@gmail.com >> <mailto:hei6m...@gmail.com> >> >> <mailto:hei6m...@gmail.com >> <mailto:hei6m...@gmail.com>>> wrote: >> >> >> >> Hi, >> >> >> >> I made some improvements to my >> patch of >> >> via stitching. Now you can just >> point >> >> copper pour place and press V, >> it make >> >> trough via. If you press >> SHIFT+CTRL+V it >> >> make buried or blind via.It >> does not >> >> change working layer. Only when >> you place >> >> buried or blind via from >> different layer >> >> than it's layer pair is. I >> think that it >> >> is quite easy to shoot board >> full of >> >> copper pours connecting vias. It is >> >> possible to remove connecting >> tracks from >> >> old designs. Just delete >> connection from >> >> pad and use clenup. Only have >> to remember >> >> that if there are not at least >> two copper >> >> pours in same netcode in >> different layers >> >> via is deleted too. Any support? >> >> >> >> >> >> Heikki >> >> >> >> On Sat, Sep 24, 2016 at 3:06 >> PM, Heikki >> >> Pulkkinen <hei6m...@gmail.com >> <mailto:hei6m...@gmail.com> >> >> <mailto:hei6m...@gmail.com >> <mailto:hei6m...@gmail.com>>> wrote: >> >> >> >> Hi everybody, >> >> >> >> This is my suggestion to >> via stitching >> >> without any tracks. It connects >> >> unconnected vias in >> different copper >> >> pours witch has same >> netcode. Adding >> >> vias is normal routing >> process without >> >> routing tracks. Start - >> Change Layer - >> >> End. Tool that do those things >> >> automatically would be >> good, so you >> >> can add all vias in same >> layer. After >> >> adding vias, run "Fill or >> Refill All >> >> Zones" that "Clenup tracks >> and vias" >> >> do not remove partly >> connected vias. >> >> >> >> >> >> Heikki >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> _______________________________________________ >> >> Mailing list: >> https://launchpad.net/~kicad-developers >> <https://launchpad.net/%7Ekicad-developers> >> >> <https://launchpad.net/%7Ekicad-developers >> <https://launchpad.net/%7Ekicad-developers>> >> >> Post to : >> kicad-developers@lists.launchpad.net >> <mailto:kicad-developers@lists.launchpad.net> >> >> <mailto:kicad-developers@lists.launchpad.net >> <mailto:kicad-developers@lists.launchpad.net>> >> >> Unsubscribe : >> https://launchpad.net/~kicad-developers >> <https://launchpad.net/%7Ekicad-developers> >> >> <https://launchpad.net/%7Ekicad-developers >> <https://launchpad.net/%7Ekicad-developers>> >> >> More help : >> https://help.launchpad.net/ListHelp >> <https://help.launchpad.net/ListHelp> >> >> <https://help.launchpad.net/ListHelp >> <https://help.launchpad.net/ListHelp>> >> >> >> >> >> >> >> >> >> >> >> >> >> >> _______________________________________________ >> >> Mailing list: https://launchpad.net/~kicad-developers >> <https://launchpad.net/%7Ekicad-developers> >> >> Post to : kicad-developers@lists.launchpad.net >> <mailto:kicad-developers@lists.launchpad.net> >> >> Unsubscribe : https://launchpad.net/~kicad-developers >> <https://launchpad.net/%7Ekicad-developers> >> >> More help : https://help.launchpad.net/ListHelp >> <https://help.launchpad.net/ListHelp> >> > >> > >> >> >> >> >> >> _______________________________________________ >> Mailing list: https://launchpad.net/~kicad-developers >> Post to : kicad-developers@lists.launchpad.net >> Unsubscribe : https://launchpad.net/~kicad-developers >> More help : https://help.launchpad.net/ListHelp > > > > > _______________________________________________ > Mailing list: https://launchpad.net/~kicad-developers > Post to : kicad-developers@lists.launchpad.net > Unsubscribe : https://launchpad.net/~kicad-developers > More help : https://help.launchpad.net/ListHelp > _______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : kicad-developers@lists.launchpad.net Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
