In my case the bug is in the receiving direction. I see no problems with
transmitting.
Here is the output of lspci -vv (for only the ethernet controller in
question) on the broken system. Below, I have the output from the
working system.
Broken system:
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411
PCI Express Gigabit Ethernet Controller (rev 15)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI
Express Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at a1204000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at a1200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 10.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+,
NROPrPrP-, LTR+
10BitTagComp-, 10BitTagReq-, OBFF Via message/WAKE#,
ExtFmt-, EETLPPrefix-
EmergencyPowerReduction Not Supported,
EmergencyPowerReductionInit-
FRS-, TPHComp-, ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn-
ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 3145728ns
Max no snoop latency: 3145728ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=81920ns
L1SubCtl2: T_PwrOn=150us
Kernel driver in use: r8169
Kernel modules: r8169
Working system:
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411
PCI Express Gigabit Ethernet Controller (rev 07)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI
Express Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at dfe00000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at 2ffff00000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 10.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+,
NROPrPrP-, LTR-
10BitTagComp-, 10BitTagReq-, OBFF Not Supported,
ExtFmt-, EETLPPrefix-
EmergencyPowerReduction Not Supported,
EmergencyPowerReductionInit-
FRS-, TPHComp-, ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Input/output error
Not readable
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn-
ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
Kernel driver in use: r8169
Kernel modules: r8169
The diffs show I have a more recent chip in the broken system (Working has Rev
7, Broken has Rev 15). There are some other differences. As mentioned in an
earlier comment it's only the broken system that says it has L1 PM Substates.
Here is the complete diff.
--- lspci-working 2020-07-16 13:59:01.156191723 -0700
+++ lspci-broken 2020-07-16 13:58:02.344788308 -0700
@@ -1,12 +1,12 @@
-01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411
PCI Express Gigabit Ethernet Controller (rev 07)
+01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411
PCI Express Gigabit Ethernet Controller (rev 15)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI
Express Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
- Interrupt: pin A routed to IRQ 19
- Region 0: I/O ports at e000 [size=256]
- Region 2: Memory at dfe00000 (64-bit, non-prefetchable) [size=4K]
- Region 4: Memory at 2ffff00000 (64-bit, prefetchable) [size=16K]
+ Interrupt: pin A routed to IRQ 18
+ Region 0: I/O ports at 3000 [size=256]
+ Region 2: Memory at a1204000 (64-bit, non-prefetchable) [size=4K]
+ Region 4: Memory at a1200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
@@ -17,20 +17,20 @@
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 10.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
- MaxPayload 128 bytes, MaxReadReq 512 bytes
+ MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
Latency L0s unlimited, L1 <64us
- ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
+ ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+,
NROPrPrP-, LTR-
- 10BitTagComp-, 10BitTagReq-, OBFF Not Supported,
ExtFmt-, EETLPPrefix-
+ DevCap2: Completion Timeout: Range ABCD, TimeoutDis+,
NROPrPrP-, LTR+
+ 10BitTagComp-, 10BitTagReq-, OBFF Via message/WAKE#,
ExtFmt-, EETLPPrefix-
EmergencyPowerReduction Not Supported,
EmergencyPowerReductionInit-
FRS-, TPHComp-, ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
@@ -40,10 +40,7 @@
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
- Capabilities: [d0] Vital Product Data
-pcilib: sysfs_read_vpd: read failed: Input/output error
- Not readable
- Capabilities: [100 v1] Advanced Error Reporting
+ Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
@@ -62,5 +59,14 @@
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
+ Capabilities: [170 v1] Latency Tolerance Reporting
+ Max snoop latency: 3145728ns
+ Max no snoop latency: 3145728ns
+ Capabilities: [178 v1] L1 PM Substates
+ L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
L1_PM_Substates+
+ PortCommonModeRestoreTime=150us
PortTPowerOnTime=150us
+ L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
+ T_CommonMode=0us LTR1.2_Threshold=81920ns
+ L1SubCtl2: T_PwrOn=150us
Kernel driver in use: r8169
Kernel modules: r8169
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1880076
Title:
ubuntu 20.4 - retransmitts with r8169
Status in linux package in Ubuntu:
Incomplete
Bug description:
Hi,
i run some network-tests (iperf3) and noticed massive retransmitts in
ubuntu 20.4 with kernel 5.4.0-29. I'm using module r8169 for network-
adapter
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 15)
if i boot my ubuntu 18.4 and did same iperf-test (same hardware, same
network configuration, other client is not rebooted) i have not these
retransmitts.
root@bpi-r2:~# iperf3 -c 192.168.0.21
Connecting to host 192.168.0.21, port 5201
[ 5] local 192.168.0.11 port 35702 connected to 192.168.0.21 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 14.2 MBytes 119 Mbits/sec 337 14.1 KBytes
[ 5] 1.00-2.00 sec 14.9 MBytes 125 Mbits/sec 331 14.1 KBytes
[ 5] 2.00-3.00 sec 15.1 MBytes 126 Mbits/sec 296 19.8 KBytes
[ 5] 3.00-4.00 sec 14.7 MBytes 124 Mbits/sec 314 14.1 KBytes
[ 5] 4.00-5.00 sec 12.8 MBytes 107 Mbits/sec 259 14.1 KBytes
[ 5] 5.00-6.01 sec 67.4 MBytes 560 Mbits/sec 137 362 KBytes
[ 5] 6.01-7.00 sec 111 MBytes 940 Mbits/sec 0 366 KBytes
[ 5] 7.00-8.00 sec 112 MBytes 941 Mbits/sec 0 409 KBytes
[ 5] 8.00-9.00 sec 112 MBytes 940 Mbits/sec 0 421 KBytes
[ 5] 9.00-10.00 sec 112 MBytes 936 Mbits/sec 0 426 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 586 MBytes 491 Mbits/sec 1674 sender
[ 5] 0.00-10.01 sec 585 MBytes 491 Mbits/sec
receiver
iperf Done.
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
group default qlen 1000
link/ether e4:b9:7a:f7:c4:8b brd ff:ff:ff:ff:ff:ff
inet 192.168.0.21/24 brd 192.168.0.255 scope global dynamic noprefixroute
enp3s0
valid_lft 171856sec preferred_lft 171856sec
inet6 fe80::781a:829f:5030:ad6a/64 scope link noprefixroute
valid_lft forever preferred_lft forever
$ ethtool -S enp3s0
NIC statistics:
tx_packets: 571053
rx_packets: 1184934
tx_errors: 0
rx_errors: 0
rx_missed: 1919 <<<<<<<<<<<<<<<<<<<<<<<<<<<
align_errors: 0
tx_single_collisions: 0
tx_multi_collisions: 0
unicast: 1184926
broadcast: 6
multicast: 2
tx_aborted: 0
tx_underrun: 0
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP
mode DEFAULT group default qlen 1000
link/ether e4:b9:7a:f7:c4:8b brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped overrun mcast
1785166133 1184970 0 0 0 2
TX: bytes packets errors dropped carrier collsns
39395440 570500 0 0 0 0
on the other side i see dropped packets, maybe flowcontrol-related?
ethtool reports "Link partner advertised pause frame use: Symmetric"
but maybe flowcontrol is not working...
also driver reports flowcontrol is enabled...
$ dmesg | grep r8169
[ 0.939358] libphy: r8169: probed
[ 0.939491] r8169 0000:03:00.0 eth0: RTL8168h/8111h, e4:b9:7a:f7:c4:8b,
XID 541, IRQ 128
[ 0.939492] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes,
tx checksumming: ko]
[ 0.986853] r8169 0000:03:00.0 enp3s0: renamed from eth0
[ 3.478981] Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver
[Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
[ 3.591124] r8169 0000:03:00.0 enp3s0: Link is Down
[ 7.171198] r8169 0000:03:00.0 enp3s0: Link is Up - 1Gbps/Full - flow
control rx/tx
ProblemType: Bug
DistroRelease: Ubuntu 20.04
Package: linux-image-5.4.0-29-generic 5.4.0-29.33
ProcVersionSignature: Ubuntu 5.4.0-29.33-generic 5.4.30
Uname: Linux 5.4.0-29-generic x86_64
ApportVersion: 2.20.11-0ubuntu27
Architecture: amd64
AudioDevicesInUse:
USER PID ACCESS COMMAND
/dev/snd/controlC0: frank 1427 F.... pulseaudio
CasperMD5CheckResult: skip
CurrentDesktop: GNOME-Flashback:GNOME
Date: Fri May 22 06:49:34 2020
InstallationDate: Installed on 2020-04-27 (24 days ago)
InstallationMedia: Ubuntu 20.04 LTS "Focal Fossa" - Release amd64 (20200423)
MachineType: Dell Inc. G5 5590
ProcEnviron:
TERM=xterm-256color
PATH=(custom, no user)
XDG_RUNTIME_DIR=<set>
LANG=de_DE.UTF-8
SHELL=/bin/bash
ProcFB: 0 i915drmfb
ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-5.4.0-29-generic
root=UUID=7c9113b7-ca65-4c46-9435-f5d2b73bab72 ro quiet
RelatedPackageVersions:
linux-restricted-modules-5.4.0-29-generic N/A
linux-backports-modules-5.4.0-29-generic N/A
linux-firmware 1.187
SourcePackage: linux
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 02/07/2020
dmi.bios.vendor: Dell Inc.
dmi.bios.version: 1.12.0
dmi.board.name: 0KW84T
dmi.board.vendor: Dell Inc.
dmi.board.version: A00
dmi.chassis.type: 10
dmi.chassis.vendor: Dell Inc.
dmi.modalias:
dmi:bvnDellInc.:bvr1.12.0:bd02/07/2020:svnDellInc.:pnG55590:pvr:rvnDellInc.:rn0KW84T:rvrA00:cvnDellInc.:ct10:cvr:
dmi.product.family: GSeries
dmi.product.name: G5 5590
dmi.product.sku: 08EA
dmi.sys.vendor: Dell Inc.
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1880076/+subscriptions
--
Mailing list: https://launchpad.net/~kernel-packages
Post to : [email protected]
Unsubscribe : https://launchpad.net/~kernel-packages
More help : https://help.launchpad.net/ListHelp
