What Firmware does Your card have? There are many versions online and some of them are for Motherboards only (has different config for chips mounted on MB embedded chipset than for expansion card PCI/PCI_E).
-- You received this bug notification because you are a member of Kernel Packages, which is subscribed to linux in Ubuntu. https://bugs.launchpad.net/bugs/1820363 Title: NEC/Renesas PCI USB3 Cards (uPD720201) Host halt failed, -19 Status in linux package in Ubuntu: Incomplete Bug description: Hello, Using Ubuntu installation media (ubuntu-18.04.2-server-amd64.iso / ubuntu-18.04.[1-2]-live-server-amd64.iso / Ubuntu Live 18.04.2 iso / Ubuntu Mate Live Ubuntu Live 18.04.[1-2] iso) Startup is hanging with : [ 0.214796] pci 0000:0d:00.0: [1912:0014] type 00 class 0x0c0330 [ 0.215620] pci 0000:0d:00.0: reg 0x10: [mem 0xfdbf0000-0xfdbf1fff 64bit] [ 0.219160] pci 0000:0d:00.0: PME# supported from D0 D3hot D3cold [ 79.272644] xhci_hcd 0000:0d:00.0: xHCI Host Controller [ 79.272710] xhci_hcd 0000:0d:00.0: new USB bus registered, assigned bus number 7 [ 79.535236] xhci_hcd 0000:0d:00.0: Host halt failed, -19 [ 79.535291] xhci_hcd 0000:0d:00.0: can't setup: -19 [ 79.535347] xhci_hcd 0000:0d:00.0: USB bus 7 deregistered [ 79.555578] xhci_hcd 0000:0d:00.0: init 0000:0d:00.0 fail, -19 I'm facing exactly the same bug as these one: https://www.mail-archive.com/linux-usb@vger.kernel.org/msg102138.html https://bugs.gentoo.org/show_bug.cgi?id=612704 I installed Ubuntu Server 18.04.2 without the PCI card without trouble and then reinserted the PCI Card .... computer never start always hanging at the same steps as above. I managed to start only once time with the PCI card plugged by adding "pci=nomsi" to the kernel command line using an Ubuntu Mate Live media with persistence and had this output: [ 0.214796] pci 0000:0d:00.0: [1912:0014] type 00 class 0x0c0330 [ 0.215620] pci 0000:0d:00.0: reg 0x10: [mem 0xfdbf0000-0xfdbf1fff 64bit] [ 0.219160] pci 0000:0d:00.0: PME# supported from D0 D3hot D3cold [ 8.041967] xhci_hcd 0000:0d:00.0: Resetting [ 9.062082] xhci_hcd 0000:0d:00.0: timed out waiting for pending transaction; performing function level reset anyway [ 10.406071] xhci_hcd 0000:0d:00.0: not ready 1123ms after FLR; waiting [ 11.462075] xhci_hcd 0000:0d:00.0: not ready 2147ms after FLR; waiting [ 13.542072] xhci_hcd 0000:0d:00.0: not ready 4195ms after FLR; waiting [ 17.894085] xhci_hcd 0000:0d:00.0: not ready 8291ms after FLR; waiting [ 26.342086] xhci_hcd 0000:0d:00.0: not ready 16483ms after FLR; waiting [ 44.006072] xhci_hcd 0000:0d:00.0: not ready 32867ms after FLR; waiting [ 78.822072] xhci_hcd 0000:0d:00.0: not ready 65635ms after FLR; giving up [ 79.222070] xhci_hcd 0000:0d:00.0: Refused to change power state, currently in D3 [ 79.272644] xhci_hcd 0000:0d:00.0: xHCI Host Controller [ 79.272710] xhci_hcd 0000:0d:00.0: new USB bus registered, assigned bus number 7 [ 79.535236] xhci_hcd 0000:0d:00.0: Host halt failed, -19 [ 79.535291] xhci_hcd 0000:0d:00.0: can't setup: -19 [ 79.535347] xhci_hcd 0000:0d:00.0: USB bus 7 deregistered [ 79.555578] xhci_hcd 0000:0d:00.0: init 0000:0d:00.0 fail, -19 It was lucky because it never worked again. PCI card was not working but computer started. Here you can find included lspci -vv, lshw and full dmesg taken from during this unique startup with the PCI Card. I tried the same PCI Card with two computers and always had the same results. Kernel is hanging with "xhci_hcd 0000:0d:00.0: init 0000:0d:00.0 fail, -19" and nothing more. I tried this PCI Card with a CentOS 7.3 on same computer and kernel (3.10) is starting well and PCI card is fully working. Many thanks for your assistance. I apologize if it's an already reported bug. Kind Regards To manage notifications about this bug go to: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1820363/+subscriptions -- Mailing list: https://launchpad.net/~kernel-packages Post to : kernel-packages@lists.launchpad.net Unsubscribe : https://launchpad.net/~kernel-packages More help : https://help.launchpad.net/ListHelp