Hi, I confirm the bug on direct attach.
Using a fiber switch is working as expected for me.
---
1a:00.0 Fibre Channel: Emulex Corporation Zephyr-X LightPulse Fibre Channel
Host Adapter (rev 02)
Subsystem: Emulex Corporation Zephyr-X LightPulse Fibre Channel Host
Adapter
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at 97a00000 (64-bit, non-prefetchable) [size=4K]
Region 2: Memory at 97a01000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 2100 [size=256]
Expansion ROM at 97a40000 [disabled] [size=256K]
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee00000 Data: 40d2
Capabilities: [70] Vital Product Data
Product Name: LPE11002 4GB/S 2-PORT FC: PCI EXPRESS HBA SFF
DIAG OPTICS
Read-only fields:
[PN] Part number: 42C2071
[SN] Serial number: 11S43W7511Y650HY1C2YTK
[V0] Vendor specific: FC14803247
[VL] Vendor specific: FRU 43W7512
[V1] Vendor specific: IBM 42C2071 4Gb 2-Port PCIe FC
HBA for System x
[V2] Vendor specific: 42C2071
[V3] Vendor specific:
T2:E1,E8,T3:E1,E2,E3,E5,E6,E7,T6:E1,T7:E1,TB:E1
[V4] Vendor specific: 0
[V5] Vendor specific: LPe11002
[RV] Reserved: checksum good, 1 byte(s) reserved
End
Capabilities: [44] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <4us,
L1 <16us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Exit
Latency L0s <4us, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [12c v1] Power Budgeting <?>
Kernel driver in use: lpfc
Kernel modules: lpfc
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1746970
Title:
lpfc.ko module doesn't work
Status in linux package in Ubuntu:
Incomplete
Bug description:
Hi.
I have problem with HBA Emulex LPe12000 Fibre channel adapter. It
doesn't see disk on direct attach.
[ 4.015493] lpfc 0000:04:00.0: 0:1303 Link Up Event x1 received Data: x1
x1 x10 x2 x0 x0 0
[ 4.015570] lpfc 0000:04:00.0: 0:1309 Link Up Event npiv not supported in
loop topology
[ 4.016671] lpfc 0000:04:00.0: 0:(0):2858 FLOGI failure Status:x3/x18
TMO:x0 Data x1000 x0
[ 4.017627] lpfc 0000:04:00.0: 0:(0):2858 FLOGI failure Status:x3/x18
TMO:x0 Data x1000 x0
[ 4.018561] lpfc 0000:04:00.0: 0:(0):2858 FLOGI failure Status:x3/x18
TMO:x0 Data x1000 x0
[ 4.018636] lpfc 0000:04:00.0: 0:(0):0100 FLOGI failure Status:x3/x18
TMO:x0
[ 4.019713] lpfc 0000:04:00.0: 0:(0):0266 Issue NameServer Req x117 err 1
Data: x80000 x0
I have made a little investigation.
Ubuntu 16.04.3 LTS, kernel 4.10.0-28, lpfc 11.2.0.2 - no problem.
Ubuntu 17.10.1, kernel 4.13.0-21, lpfc 11.4.0.1 - problem.
Debian 9.3, kernel 4.9.0-4, lpfc 11.2.0.0 - no problem.
Fedora 27, kernel 4.13.9-300, lpfc 11.4.0.1 - problem.
Proxmox 5.0, kernel 4.10.15-1, lpfc 11.2.0.2 - no problem.
Proxmox 5.1, kernel 4.13.13-5, lpfc 11.4.0.1 - problem.
Another user with this problem said that if fiber switch is added
between the server and the storage it's working as expected.
I think problem is in lpfc.ko 11.4.0.1. Any kernel (4.13 now) that has
this module version is affected. Broadcom support confirmed that bug
and suggested to update module. But Broadcom supports only RHEL and
SLES. I tried to compile, but no luck. Please, could you update
lpfc.ko module in linux-image-generic package?
There are version 11.4.142.21 for SLES 12 and 11.4.204.11 for RHEL 6
and 7 on Broadcom site.
Thanks.
---
04:00.0 Fibre Channel [0c04]: Emulex Corporation Saturn-X: LightPulse Fibre
Channel Host Adapter [10df:f100] (rev 03)
Subsystem: Emulex Corporation Saturn-X: LightPulse Fibre Channel Host
Adapter [10df:f100]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 27
Region 0: Memory at fbaff000 (64-bit, non-prefetchable) [size=4K]
Region 2: Memory at fbaf8000 (64-bit, non-prefetchable) [size=16K]
Expansion ROM at fba80000 [disabled] [size=256K]
Capabilities: [58] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable- Count=1/16 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [78] MSI-X: Enable- Count=32 Masked-
Vector table: BAR=2 offset=00002000
PBA: BAR=2 offset=00003000
Capabilities: [84] Vital Product Data
Product Name: LPE12000, 8GB/S, 1-PORT FC, PCI EXPRESS HBA, SFP,
DIAG, OPTICS, DELL
Read-only fields:
[PN] Part number: LPE12000-M8
[SN] Serial number: FC24751316
[V0] Vendor specific: FC24751316
[V1] Vendor specific: Emulex LPe12000-M8 8Gb PCIe Fibre
Channel Adapter
[V2] Vendor specific: LPe12000-M8
[V3] Vendor specific:
T2:78,T3:79,7A,7B,7D,7E,7F,T7:73,TB:73,TFF:78
[V4] Vendor specific:
[RV] Reserved: checksum bad, 20 byte(s) reserved
End
Capabilities: [94] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 2048 bytes, PhantFunc 0, Latency L0s <1us,
L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Exit Latency
L0s <1us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-,
OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-,
LinkEqualizationRequest-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [12c v1] Power Budgeting <?>
Kernel modules: lpfc
---
ApportVersion: 2.20.7-0ubuntu3.7
Architecture: amd64
AudioDevicesInUse: Error: command ['fuser', '-v', '/dev/snd/seq',
'/dev/snd/timer'] failed with exit code 1:
CasperVersion: 1.387
DistroRelease: Ubuntu 17.10
LiveMediaBuild: Ubuntu 17.10 "Artful Aardvark" - Release amd64 (20180105.1)
MachineType: HP ProLiant DL160 G6
Package: linux (not installed)
ProcEnviron:
TERM=xterm-256color
PATH=(custom, no user)
LANG=ru_RU.UTF-8
SHELL=/bin/bash
ProcFB: 0 mgadrmfb
ProcKernelCmdLine: file=/cdrom/preseed/hostname.seed boot=casper
initrd=/casper/initrd.lz quiet splash --- debian-installer/language=ru
keyboard-configuration/layoutcode?=ru
ProcVersionSignature: Ubuntu 4.13.0-21.24-generic 4.13.13
PulseList:
Error: command ['pacmd', 'list'] failed with exit code 1: Home directory not
accessible: Permission denied
No PulseAudio daemon running, or not running as session daemon.
RelatedPackageVersions:
linux-restricted-modules-4.13.0-21-generic N/A
linux-backports-modules-4.13.0-21-generic N/A
linux-firmware 1.169.1
RfKill:
Tags: artful
Uname: Linux 4.13.0-21-generic x86_64
UpgradeStatus: No upgrade log present (probably fresh install)
UserGroups:
_MarkForUpload: True
dmi.bios.date: 05/19/2010
dmi.bios.vendor: HP
dmi.bios.version: O33
dmi.chassis.type: 23
dmi.chassis.vendor: HP
dmi.modalias:
dmi:bvnHP:bvrO33:bd05/19/2010:svnHP:pnProLiantDL160G6:pvr:cvnHP:ct23:cvr:
dmi.product.name: ProLiant DL160 G6
dmi.sys.vendor: HP
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1746970/+subscriptions
--
Mailing list: https://launchpad.net/~kernel-packages
Post to : [email protected]
Unsubscribe : https://launchpad.net/~kernel-packages
More help : https://help.launchpad.net/ListHelp
