I cannot see : "loading /boot/defaults/loader.conf" when I reset the device
BR, Mohammad On Sun, 11 Nov 2018 at 14:43, Mohammad Khalil <[email protected]> wrote: > Ops , but it did not work either > Nand format failed > > BR, > Mohammad > > On Sun, 11 Nov 2018 at 14:46, Jonas Frey <[email protected]> wrote: > >> Hi Mohammad, >> >> thats a typo, its nand_format (note the underscore). >> Am Sonntag, den 11.11.2018, 05:31 -0500 schrieb Mohammad Khalil: >> > => reset >> > >> > >> > U-Boot 1.1.6-JNPR-2.7 (Build time: Nov 26 2013 - 19:04:49) >> > >> > Initializing memory this may take some time... >> > Measured DDR clock 266.62 MHz >> > SRX_100H2 board revision major:1, minor:0, serial #: BZ4214AF1453 >> > OCTEON CN5020-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz >> > (532 >> > Mhz data rate) >> > DRAM: 2048 MB >> > Starting Memory POST... >> > Checking datalines... OK >> > Checking address lines... OK >> > Checking 512K memory for U-Boot... OK. >> > Running U-Boot CRC Test... OK. >> > Flash: 4 MB >> > USB: scanning bus for devices... 4 USB Device(s) found >> > scanning bus for storage devices... Read Error for >> > STMicroelectronics device 0 >> > Not intializing this device, disabling autoboot >> > Device may need formatting, please issue command : >> > <nand_format> at console prompt to format >> > 2 Storage Device(s) found >> > Clearing DRAM........ done >> > BIST check passed. >> > Boot Media: nand-flash usb >> > Net: pic init done (err = 0)octeth0 >> > POST Passed >> > Press SPACE to abort autoboot in 1 seconds >> > => nand-format >> > Unknown command 'nand-format' - try 'help' >> > >> > >> > On Sun, 11 Nov 2018 at 04:17, Muhammad Atif Jauhar <atif.jauhar@gmail >> > .com> >> > wrote: >> > >> > > >> > > Hi Khalil, >> > > >> > > Kindly follow below link to recover it. >> > > >> > > >> > > https://forums.juniper.net/t5/SRX-Services-Gateway/Boot-problem-of- >> > > UBoot-srx240-having-status-LED-red/td-p/211103 >> > > >> > > Regards, >> > > >> > > Muhammad Atif Jauhar >> > > (+966-56-00-04-985) >> > > >> > > >> > > On Sun, Nov 11, 2018 at 11:36 AM Mohammad Khalil <[email protected] >> > > m> >> > > wrote: >> > > >> > > > >> > > > Hello all >> > > > I have my Juniper SRX 100h stuck in the u-boot mode >> > > > I have tried to download a new image on a USB stick , plugged it >> > > > into the >> > > > device and tried to upgrade with no luck >> > > > Looked around but could not find a solution , anyone can help >> > > > please? >> > > > >> > > > BR, >> > > > Mohammad >> > > > _______________________________________________ >> > > > juniper-nsp mailing list [email protected] >> > > > https://puck.nether.net/mailman/listinfo/juniper-nsp >> > > > >> > _______________________________________________ >> > juniper-nsp mailing list [email protected] >> > https://puck.nether.net/mailman/listinfo/juniper-nsp >> > _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
