On Wed, 2021-11-10 at 07:29 +0200, Dafna Hirschfeld wrote:
>
> On 10.11.21 04:20, Yong Wu wrote:
> > On Tue, 2021-11-09 at 14:21 +0200, Dafna Hirschfeld wrote:
> > > Hi
> > > This patch is needed in order to update the tlb when a device is
> > > powered on.
> > > Could you send this patch alone without the whole series so it
> > > get
> > > accepted easier?
> >
> > Which SoC are you testing on? In previous SoC, the IOMMU HW don't
> > have
> > power-domain, and we have a "has_pm"[1] in the tlb function for
> > that
> > case. The "has_pm" should be always 0 for the previous SoC like
> > mt8173,
> > it should always tlb synchronize.
> >
> > thus, Could you help share more about your issue? In which case it
> > lack
> > the necessary tlb operation. At least, We need confirm if it needs
> > a
> > "Fixes" tags if sending this patch alone.
>
> Hi,
> I work with the mtk-vcodec driver on mt8173. As you wrote, the iommu
> doesn't
> have a power-domain and so when allocating buffers before the device
> is powered
> on, there is the warning
> "Partial TLB flush timed out, falling back to full flush"
> flooding the log buf.
oh. Thanks very much for your information. Get it now.
This issue should be introduced by the:
b34ea31fe013 ("iommu/mediatek: Always enable the clk on resume")
tlb failed due to the bclk is not enabled. Could you help try that
after reverting this?
>
> Sebastian Reichel suggested to remove the 'if(has_pm)' check to avoid
> this warning,
> and avoid flushing the tlb if the device is off:
>
> [1] http://ix.io/3Eyr
>
> This fixes the warning, but then the tlb is not flushed in sync,
> Therefore the tlb should be flushed when the device is resumed.
>
> So the two patches (the one suggested in the link [1] and this patch)
> should be sent together as a 2-patch series.
then this is reasonable. You could help this into a new patchset if you
are free(add Fixes tag).
Thanks.
>
> Thanks,
> Dafna
>
> >
> > Thanks.
> >
> > [1]
> >
https://elixir.bootlin.com/linux/v5.15/source/drivers/iommu/mtk_iommu.c#L236
> >
> > > I can resend the patch on your behalf if you want.
> > >
> > > Thanks,
> > > Dafna
> > >
> > > On 23.09.21 14:58, Yong Wu wrote:
> > > > Prepare for 2 HWs that sharing pgtable in different power-
> > > > domains.
> > > >
> > > > When there are 2 M4U HWs, it may has problem in the flush_range
> > > > in
> > > > which
> > > > we get the pm_status via the m4u dev, BUT that function don't
> > > > reflect the
> > > > real power-domain status of the HW since there may be other HW
> > > > also
> > > > use
> > > > that power-domain.
> > > >
> > > > The function dma_alloc_attrs help allocate the iommu buffer
> > > > which
> > > > need the corresponding power domain since tlb flush is needed
> > > > when
> > > > preparing iova. BUT this function only is for allocating
> > > > buffer,
> > > > we have no good reason to request the user always call
> > > > pm_runtime_get
> > > > before calling dma_alloc_xxx. Therefore, we add a tlb_flush_all
> > > > in the pm_runtime_resume to make sure the tlb always is clean.
> > > >
> > > > Another solution is always call pm_runtime_get in the
> > > > tlb_flush_range.
> > > > This will trigger pm runtime resume/backup so often when the
> > > > iommu
> > > > power is not active at some time(means user don't call
> > > > pm_runtime_get
> > > > before calling dma_alloc_xxx), This may cause the performance
> > > > drop.
> > > > thus we don't use this.
> > > >
> > > > In other case, the iommu's power should always be active via
> > > > device
> > > > link with smi.
> > > >
> > > > The previous SoC don't have PM except mt8192. the mt8192 IOMMU
> > > > is
> > > > display's
> > > > power-domain which nearly always is enabled. thus no need fix
> > > > tags
> > > > here.
> > > > Prepare for mt8195.
> > > >
> > > > Signed-off-by: Yong Wu <yong...@mediatek.com>
> > > > ---
> > > > drivers/iommu/mtk_iommu.c | 11 +++++++++++
> > > > 1 file changed, 11 insertions(+)
> > > >
> > > > diff --git a/drivers/iommu/mtk_iommu.c
> > > > b/drivers/iommu/mtk_iommu.c
> > > > index 44cf5547d084..e9e94944ed91 100644
> > > > --- a/drivers/iommu/mtk_iommu.c
> > > > +++ b/drivers/iommu/mtk_iommu.c
> > > > @@ -984,6 +984,17 @@ static int __maybe_unused
> > > > mtk_iommu_runtime_resume(struct device *dev)
> > > > return ret;
> > > > }
> > > >
> > > > + /*
> > > > + * Users may allocate dma buffer before they call
> > > > pm_runtime_get, then
> > > > + * it will lack the necessary tlb flush.
> > > > + *
> > > > + * We have no good reason to request the users always
> > > > call
> > > > dma_alloc_xx
> > > > + * after pm_runtime_get_sync.
> > > > + *
> > > > + * Thus, Make sure the tlb always is clean after each
> > > > PM
> > > > resume.
> > > > + */
> > > > + mtk_iommu_tlb_do_flush_all(data);
> > > > +
> > > > /*
> > > > * Uppon first resume, only enable the clk and return,
> > > > since
> > > > the values of the
> > > > * registers are not yet set.
> > > >
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu
