On Fri, Aug 14, 2015 at 04:03:55PM +0300, Ville Syrjälä wrote: > On Fri, Aug 14, 2015 at 10:30:26AM +0200, Daniel Vetter wrote: > > On Wed, Aug 12, 2015 at 09:34:54PM +0300, Ville Syrjälä wrote: > > > On Fri, Jul 31, 2015 at 03:13:52PM +0300, Mika Kahola wrote: > > > > It is possible the we request to have a mode that has > > > > higher pixel clock than our HW can support. This patch > > > > checks if requested pixel clock is lower than the one > > > > supported by the HW. The requested mode is discarded > > > > if we cannot support the requested pixel clock. > > > > > > > > This patch applies to HDMI. > > > > > > > > V2: > > > > - removed computation for max dot clock > > > > > > > > V3: > > > > - cleanup by removing unnecessary lines > > > > > > > > Signed-off-by: Mika Kahola <mika.kah...@intel.com> > > > > --- > > > > drivers/gpu/drm/i915/intel_hdmi.c | 4 ++++ > > > > 1 file changed, 4 insertions(+) > > > > > > > > diff --git a/drivers/gpu/drm/i915/intel_hdmi.c > > > > b/drivers/gpu/drm/i915/intel_hdmi.c > > > > index 70bad5b..3149e5f 100644 > > > > --- a/drivers/gpu/drm/i915/intel_hdmi.c > > > > +++ b/drivers/gpu/drm/i915/intel_hdmi.c > > > > @@ -1193,10 +1193,14 @@ intel_hdmi_mode_valid(struct drm_connector > > > > *connector, > > > > struct drm_device *dev = intel_hdmi_to_dev(hdmi); > > > > enum drm_mode_status status; > > > > int clock; > > > > + int max_pixclk = to_i915(connector->dev)->max_dotclk; > > > > > > > > if (mode->flags & DRM_MODE_FLAG_DBLSCAN) > > > > return MODE_NO_DBLESCAN; > > > > > > > > + if (mode->clock > max_pixclk) > > > > + return MODE_CLOCK_HIGH; > > > > + > > > > clock = mode->clock; > > > > > > I believe we should do something like this here: > > > > > > clock = mode->clock; > > > > > > if ((mode->flags & DRM_MODE_FLAG_3D_MASK) == > > > DRM_MODE_FLAG_3D_FRAME_PACKING) > > > clock *= 2; > > > > That's already done in drm_mode_set_crtcinfo, i915 uses the STEREO_DOUBLE > > mode of that function. > > Only for modesets. .mode_valid() only deals with the results of > .get_modes() etc., so the timings won't have been doubled. And even then > we only double the .crtc_ timings, which is where I previously gave up > trying to use the same mode validation code during modeset and .fill_modes(). > I suppose we can make it happen if we really try, but in the meantime I > think it's at least an improvement if we stop advertising modes we for > sure can't use.
Oh right totally mixed things up, you're correct. -Daniel > > > -Daniel > > > > > > > > if (clock > max_pixclk) > > > return MODE_CLOCK_HIGH; > > > > > > > if (mode->flags & DRM_MODE_FLAG_DBLCLK) > > > > clock *= 2; > > > > > > The stero handling should probably be in a separate patch, but in > > > preparation for it you could already put the dotclk check between the > > > clock= assigment and the DBCLK doubling (since DBLCLK only affects the > > > port_clock and not pixel clock). > > > > > > > -- > > > > 1.9.1 > > > > > > > > _______________________________________________ > > > > Intel-gfx mailing list > > > > Intel-gfx@lists.freedesktop.org > > > > http://lists.freedesktop.org/mailman/listinfo/intel-gfx > > > > > > -- > > > Ville Syrjälä > > > Intel OTC > > > _______________________________________________ > > > Intel-gfx mailing list > > > Intel-gfx@lists.freedesktop.org > > > http://lists.freedesktop.org/mailman/listinfo/intel-gfx > > > > -- > > Daniel Vetter > > Software Engineer, Intel Corporation > > http://blog.ffwll.ch > > -- > Ville Syrjälä > Intel OTC -- Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list Intel-gfx@lists.freedesktop.org http://lists.freedesktop.org/mailman/listinfo/intel-gfx
