On Wednesday 11 December 2013 04:32 PM, Jani Nikula wrote:
On Tue, 10 Dec 2013, Shobhit Kumar <shobhit.ku...@intel.com> wrote:Basically ULPS handling during enable/disable has been moved to pre_enable and post_disable phases. PLL and panel power disable also has been moved to post_disable phase. The ULPS entry/exit sequneces as suggested by HW team is as follows - During enable time - set DEVICE_READY --> Clear DEVICE_READY --> set DEVICE_READY And during disable time to flush all FIFOs - set ENTER_SLEEP --> EXIT_SLEEP --> ENTER_SLEEP Also during disbale sequnece sub-encoder disable is moved to the end after port is disabled. v2: Based on comments from Ville - Detailed epxlaination in the commit messgae - Moved parameter changes out into another patch - Backlight enabling will be a new patch v3: Updated as per Jani's comments - Removed the I915_WRITE_BITS as it is not needed - Moved panel_reset and send_otp_cmds hooks to dsi_pre_enable - Moved disable_panel_power hook to dsi_post_disable - Replace hardcoding with AFE_LATCHOUT Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimu...@intel.com> Signed-off-by: Shobhit Kumar <shobhit.ku...@intel.com> --- drivers/gpu/drm/i915/intel_dsi.c | 110 +++++++++++++++++++++++++++------------ drivers/gpu/drm/i915/intel_dsi.h | 2 + 2 files changed, 79 insertions(+), 33 deletions(-) diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c index 1016e7b..01b9f3a 100644 --- a/drivers/gpu/drm/i915/intel_dsi.c +++ b/drivers/gpu/drm/i915/intel_dsi.c @@ -101,46 +101,57 @@ static void intel_dsi_pre_pll_enable(struct intel_encoder *encoder) vlv_enable_dsi_pll(encoder); } -static void intel_dsi_pre_enable(struct intel_encoder *encoder) +void intel_dsi_device_ready(struct intel_encoder *encoder)Should be static.{ + struct drm_i915_private *dev_priv = encoder->base.dev->dev_private; + struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc); + int pipe = intel_crtc->pipe; + u32 val; + DRM_DEBUG_KMS("\n"); -} -static void intel_dsi_enable(struct intel_encoder *encoder) + val = I915_READ(MIPI_PORT_CTRL(pipe)); + I915_WRITE(MIPI_PORT_CTRL(pipe), val | LP_OUTPUT_HOLD); + usleep_range(1000, 1500); + I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY | ULPS_STATE_EXIT); + usleep_range(2000, 2500); + I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY); + usleep_range(2000, 2500); + I915_WRITE(MIPI_DEVICE_READY(pipe), 0x00); + usleep_range(2000, 2500); + I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY); + usleep_range(2000, 2500); +} +static void intel_dsi_pre_enable(struct intel_encoder *encoder) { - struct drm_i915_private *dev_priv = encoder->base.dev->dev_private; - struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc); struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base); - int pipe = intel_crtc->pipe; - u32 temp; DRM_DEBUG_KMS("\n"); if (intel_dsi->dev.dev_ops->panel_reset) intel_dsi->dev.dev_ops->panel_reset(&intel_dsi->dev); - temp = I915_READ(MIPI_DEVICE_READY(pipe)); - if ((temp & DEVICE_READY) == 0) { - temp &= ~ULPS_STATE_MASK; - I915_WRITE(MIPI_DEVICE_READY(pipe), temp | DEVICE_READY); - } else if (temp & ULPS_STATE_MASK) { - temp &= ~ULPS_STATE_MASK; - I915_WRITE(MIPI_DEVICE_READY(pipe), temp | ULPS_STATE_EXIT); - /* - * We need to ensure that there is a minimum of 1 ms time - * available before clearing the UPLS exit state. - */ - msleep(2); - I915_WRITE(MIPI_DEVICE_READY(pipe), temp); - } + /* put device in ready state */ + intel_dsi_device_ready(encoder); if (intel_dsi->dev.dev_ops->send_otp_cmds) intel_dsi->dev.dev_ops->send_otp_cmds(&intel_dsi->dev); +} + +static void intel_dsi_enable(struct intel_encoder *encoder) +{ + struct drm_device *dev = encoder->base.dev; + struct drm_i915_private *dev_priv = dev->dev_private; + struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc); + struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base); + int pipe = intel_crtc->pipe; + u32 temp; + + DRM_DEBUG_KMS("\n"); if (is_cmd_mode(intel_dsi)) I915_WRITE(MIPI_MAX_RETURN_PKT_SIZE(pipe), 8 * 4); - - if (is_vid_mode(intel_dsi)) { + else { msleep(20); /* XXX */ dpi_send_cmd(intel_dsi, TURN_ON); msleep(100); @@ -157,7 +168,8 @@ static void intel_dsi_enable(struct intel_encoder *encoder) static void intel_dsi_disable(struct intel_encoder *encoder) { - struct drm_i915_private *dev_priv = encoder->base.dev->dev_private; + struct drm_device *dev = encoder->base.dev; + struct drm_i915_private *dev_priv = dev->dev_private; struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc); struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base); int pipe = intel_crtc->pipe; @@ -165,8 +177,6 @@ static void intel_dsi_disable(struct intel_encoder *encoder) DRM_DEBUG_KMS("\n"); - intel_dsi->dev.dev_ops->disable(&intel_dsi->dev); - if (is_vid_mode(intel_dsi)) { dpi_send_cmd(intel_dsi, SHUTDOWN); msleep(10); @@ -179,20 +189,54 @@ static void intel_dsi_disable(struct intel_encoder *encoder) msleep(2); } - temp = I915_READ(MIPI_DEVICE_READY(pipe)); - if (temp & DEVICE_READY) { - temp &= ~DEVICE_READY; - temp &= ~ULPS_STATE_MASK; - I915_WRITE(MIPI_DEVICE_READY(pipe), temp); - } + /* if disable packets are sent before sending shutdown packet then in + * some next enable sequence send turn on packet error is observed */ + if (intel_dsi->dev.dev_ops->disable) + intel_dsi->dev.dev_ops->disable(&intel_dsi->dev); } -static void intel_dsi_post_disable(struct intel_encoder *encoder) +void intel_dsi_clear_device_ready(struct intel_encoder *encoder)Should be static. With these fixed, Reviewed-by: Jani Nikula <jani.nik...@intel.com>
Yeah sending the updated patch Regards Shobhit _______________________________________________ Intel-gfx mailing list Intel-gfx@lists.freedesktop.org http://lists.freedesktop.org/mailman/listinfo/intel-gfx
