On Mon, 03 Feb 2020, Vandita Kulkarni <vandita.kulka...@intel.com> wrote:
> Configure the transcoder to operate in TE GATE command mode
> and take TE events from GPIO.
> Also disable the periodic command mode, that GOP would have
> programmed.
>
> v2: Disable util pin (Jani)
>
> Signed-off-by: Vandita Kulkarni <vandita.kulka...@intel.com>
> ---
> drivers/gpu/drm/i915/display/icl_dsi.c | 52 ++++++++++++++++++++++++++
> 1 file changed, 52 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/display/icl_dsi.c
> b/drivers/gpu/drm/i915/display/icl_dsi.c
> index d842e280699d..ce5e38c16201 100644
> --- a/drivers/gpu/drm/i915/display/icl_dsi.c
> +++ b/drivers/gpu/drm/i915/display/icl_dsi.c
> @@ -744,6 +744,18 @@ gen11_dsi_configure_transcoder(struct intel_encoder
> *encoder,
> tmp |= VIDEO_MODE_SYNC_PULSE;
> break;
> }
> + } else {
> + /*
> + * FIXME: Retrieve this info from VBT.
> + * As per the spec when dsi transcoder is operating
> + * in TE GATE mode, TE comes from GPIO
> + * which is UTIL PIN for DSI 0.
> + * Also this GPIO would not be used for other
> + * purposes is an assumption.
> + */
> + tmp &= ~OP_MODE_MASK;
> + tmp |= CMD_MODE_TE_GATE;
> + tmp |= TE_SOURCE_GPIO;
> }
>
> intel_de_write(dev_priv, DSI_TRANS_FUNC_CONF(dsi_trans), tmp);
> @@ -1016,6 +1028,32 @@ static void gen11_dsi_setup_timeouts(struct
> intel_encoder *encoder,
> }
> }
>
> +static void gen11_dsi_config_util_pin(struct intel_encoder *encoder,
> + bool enable)
> +{
> + struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> + struct intel_dsi *intel_dsi = enc_to_intel_dsi(&encoder->base);
> + u32 tmp;
> +
> + /*
> + * used as TE i/p for DSI0,
> + * for dual link/DSI1 TE is from slave DSI1
> + * through GPIO.
> + */
> + if (is_vid_mode(intel_dsi) || (intel_dsi->ports & BIT(PORT_B)))
> + return;
> +
> + tmp = I915_READ(UTIL_PIN_CTL);
> +
> + if (enable) {
> + tmp |= UTIL_PIN_DIRECTION_INPUT;
> + tmp |= UTIL_PIN_ENABLE;
> + } else {
> + tmp &= ~UTIL_PIN_ENABLE;
> + }
> + I915_WRITE(UTIL_PIN_CTL, tmp);
Please use intel_de_read() and intel_de_write().
> +}
> +
> static void
> gen11_dsi_enable_port_and_phy(struct intel_encoder *encoder,
> const struct intel_crtc_state *crtc_state)
> @@ -1037,6 +1075,9 @@ gen11_dsi_enable_port_and_phy(struct intel_encoder
> *encoder,
> /* setup D-PHY timings */
> gen11_dsi_setup_dphy_timings(encoder, crtc_state);
>
> + /* Since transcoder is configured to take events from GPIO */
> + gen11_dsi_config_util_pin(encoder, true);
> +
> /* step 4h: setup DSI protocol timeouts */
> gen11_dsi_setup_timeouts(encoder, crtc_state);
>
> @@ -1180,6 +1221,15 @@ static void gen11_dsi_deconfigure_trancoder(struct
> intel_encoder *encoder)
> enum transcoder dsi_trans;
> u32 tmp;
>
> + /* disable periodic update mode */
> + if (is_cmd_mode(intel_dsi)) {
> + for_each_dsi_port(port, intel_dsi->ports) {
> + tmp = I915_READ(DSI_CMD_FRMCTL(port));
> + tmp &= ~DSI_PERIODIC_FRAME_UPDATE_ENABLE;
> + I915_WRITE(DSI_CMD_FRMCTL(port), tmp);
Ditto. With those fixed,
Reviewed-by: Jani Nikula <jani.nik...@intel.com>
> + }
> + }
> +
> /* put dsi link in ULPS */
> for_each_dsi_port(port, intel_dsi->ports) {
> dsi_trans = dsi_port_to_transcoder(port);
> @@ -1286,6 +1336,8 @@ static void gen11_dsi_disable(struct intel_encoder
> *encoder,
> /* step3: disable port */
> gen11_dsi_disable_port(encoder);
>
> + gen11_dsi_config_util_pin(encoder, false);
> +
> /* step4: disable IO power */
> gen11_dsi_disable_io_power(encoder);
> }
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
