Op 10-10-2019 om 14:39 schreef Ville Syrjälä:
> On Thu, Oct 10, 2019 at 01:56:42PM +0200, Maarten Lankhorst wrote:
>> Op 08-10-2019 om 19:03 schreef Ville Syrjälä:
>>> On Fri, Oct 04, 2019 at 01:34:57PM +0200, Maarten Lankhorst wrote:
>>>> Use this in all the places where we try to acquire planes after the planes
>>>> atomic_check().
>>>>
>>>> In case of intel_modeset_all_pipes() this is not yet done after
>>>> atomic_check,
>>>> but seems like it will be in the future. To add some paranoia, add all
>>>> planes
>>>> rather than active planes, because of bigjoiner and planar YUV support
>>>> having
>>>> extra planes outside of the core's view that wouldn't be added otherwise.
>>> If the plane isn't active what good does adding it do?
>>>
>>> Maybe the only real exception I can think of is the watermarks
>>> and the primary vs. gamma/csc_enable on pre-skl, but those are
>>> already handled correctly.
>> Planar YUV Y planes are not enumerated, so it's useful to add. Instead of
>> typing up special case support I thought it was easier to just add all
>> planes. On bigjoiner slave no planes are enabled either, even if they're
>> active.
> I think once we have the state split we should get rid of all the
> special casing of the Y planes. Then they (and the bigjoiner slave
> planes) should just look like an active planes which is not
> logically enabled by uapi.
With the plane split it's doable, even for watermarks, but prefer to do it
later on, not change the world too much. :)
There is no issue in the core with adding planes that are disabled, so I don't
see the problem?
~Maarten
>>>> Signed-off-by: Maarten Lankhorst <maarten.lankho...@linux.intel.com>
>>>> ---
>>>> drivers/gpu/drm/i915/display/intel_atomic.c | 41 +++++++++----------
>>>> .../gpu/drm/i915/display/intel_atomic_plane.c | 19 +++++++++
>>>> drivers/gpu/drm/i915/display/intel_cdclk.c | 15 ++++---
>>>> drivers/gpu/drm/i915/display/intel_color.c | 7 ++--
>>>> .../drm/i915/display/intel_display_types.h | 6 +++
>>>> drivers/gpu/drm/i915/intel_pm.c | 14 ++++---
>>>> 6 files changed, 66 insertions(+), 36 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_atomic.c
>>>> b/drivers/gpu/drm/i915/display/intel_atomic.c
>>>> index c5a552a69752..e6cb85d41c8d 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_atomic.c
>>>> +++ b/drivers/gpu/drm/i915/display/intel_atomic.c
>>>> @@ -313,13 +313,10 @@ int intel_atomic_setup_scalers(struct
>>>> drm_i915_private *dev_priv,
>>>> struct intel_crtc *intel_crtc,
>>>> struct intel_crtc_state *crtc_state)
>>>> {
>>>> - struct drm_plane *plane = NULL;
>>>> - struct intel_plane *intel_plane;
>>>> - struct intel_plane_state *plane_state = NULL;
>>>> struct intel_crtc_scaler_state *scaler_state =
>>>> &crtc_state->scaler_state;
>>>> struct drm_atomic_state *drm_state = crtc_state->base.state;
>>>> - struct intel_atomic_state *intel_state =
>>>> to_intel_atomic_state(drm_state);
>>>> + struct intel_atomic_state *state = to_intel_atomic_state(drm_state);
>>>> int num_scalers_need;
>>>> int i;
>>>>
>>>> @@ -346,6 +343,7 @@ int intel_atomic_setup_scalers(struct drm_i915_private
>>>> *dev_priv,
>>>>
>>>> /* walkthrough scaler_users bits and start assigning scalers */
>>>> for (i = 0; i < sizeof(scaler_state->scaler_users) * 8; i++) {
>>>> + struct intel_plane_state *plane_state = NULL;
>>>> int *scaler_id;
>>>> const char *name;
>>>> int idx;
>>>> @@ -361,19 +359,16 @@ int intel_atomic_setup_scalers(struct
>>>> drm_i915_private *dev_priv,
>>>> /* panel fitter case: assign as a crtc scaler */
>>>> scaler_id = &scaler_state->scaler_id;
>>>> } else {
>>>> - name = "PLANE";
>>>> + struct intel_plane *plane;
>>>>
>>>> /* plane scaler case: assign as a plane scaler */
>>>> /* find the plane that set the bit as scaler_user */
>>>> - plane = drm_state->planes[i].ptr;
>>>>
>>>> /*
>>>> * to enable/disable hq mode, add planes that are using
>>>> scaler
>>>> * into this transaction
>>>> */
>>>> - if (!plane) {
>>>> - struct drm_plane_state *state;
>>>> -
>>>> + if (!drm_state->planes[i].ptr) {
>>>> /*
>>>> * GLK+ scalers don't have a HQ mode so it
>>>> * isn't necessary to change between HQ and dyn
>>>> mode
>>>> @@ -382,24 +377,28 @@ int intel_atomic_setup_scalers(struct
>>>> drm_i915_private *dev_priv,
>>>> if (INTEL_GEN(dev_priv) >= 10 ||
>>>> IS_GEMINILAKE(dev_priv))
>>>> continue;
>>>>
>>>> - plane = drm_plane_from_index(&dev_priv->drm, i);
>>>> - state = drm_atomic_get_plane_state(drm_state,
>>>> plane);
>>>> - if (IS_ERR(state)) {
>>>> - DRM_DEBUG_KMS("Failed to add [PLANE:%d]
>>>> to drm_state\n",
>>>> - plane->base.id);
>>>> - return PTR_ERR(state);
>>>> + plane =
>>>> to_intel_plane(drm_plane_from_index(&dev_priv->drm, i));
>>>> + plane_state =
>>>> +
>>>> intel_atomic_get_plane_state_after_check(state,
>>>> +
>>>> crtc_state,
>>>> +
>>>> plane);
>>>> + if (IS_ERR(plane_state)) {
>>>> + DRM_DEBUG_KMS("Failed to add [PLANE:%d]
>>>> to drm_state: %li\n",
>>>> + plane->base.base.id,
>>>> PTR_ERR(plane_state));
>>>> + return PTR_ERR(plane_state);
>>>> }
>>>> + } else {
>>>> + plane =
>>>> to_intel_plane(drm_state->planes[i].ptr);
>>>> + plane_state =
>>>> intel_atomic_get_new_plane_state(state,
>>>> +
>>>> plane);
>>>> }
>>>>
>>>> - intel_plane = to_intel_plane(plane);
>>>> - idx = plane->base.id;
>>>> -
>>>> /* plane on different crtc cannot be a scaler user of
>>>> this crtc */
>>>> - if (WARN_ON(intel_plane->pipe != intel_crtc->pipe))
>>>> + if (WARN_ON(plane->pipe != intel_crtc->pipe))
>>>> continue;
>>>>
>>>> - plane_state =
>>>> intel_atomic_get_new_plane_state(intel_state,
>>>> -
>>>> intel_plane);
>>>> + name = "PLANE";
>>>> + idx = plane->base.base.id;
>>>> scaler_id = &plane_state->scaler_id;
>>>> }
>>>>
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_atomic_plane.c
>>>> b/drivers/gpu/drm/i915/display/intel_atomic_plane.c
>>>> index 98b7766eaa7a..4eaab0de98bf 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_atomic_plane.c
>>>> +++ b/drivers/gpu/drm/i915/display/intel_atomic_plane.c
>>>> @@ -366,6 +366,25 @@ void i9xx_update_planes_on_crtc(struct
>>>> intel_atomic_state *state,
>>>> }
>>>> }
>>>>
>>>> +struct intel_plane_state *
>>>> +intel_atomic_get_plane_state_after_check(struct intel_atomic_state *state,
>>>> + struct intel_crtc_state
>>>> *new_crtc_state,
>>>> + struct intel_plane *plane)
>>>> +{
>>>> + struct intel_plane_state *plane_state =
>>>> + intel_atomic_get_new_plane_state(state, plane);
>>>> +
>>>> + if (plane_state)
>>>> + return plane_state;
>>>> +
>>>> + plane_state = intel_atomic_get_plane_state(state, plane);
>>>> + if (IS_ERR(plane_state))
>>>> + return plane_state;
>>>> +
>>>> + new_crtc_state->update_planes |= BIT(plane->id);
>>> I also don't really like burying this all the way down. Seems
>>> rather non-obvious from the caller. Also seems wrong to not set
>>> the flag if the plane was already part of the state.
>>>
>>> I'd say we just need to hand roll add_affected_planes() for the
>>> cdclk code. And there is should definitely be sufficient to
>>> add just the active planes.
>>>
>>>> + return plane_state;
>>>> +}
>>>> +
>>>> const struct drm_plane_helper_funcs intel_plane_helper_funcs = {
>>>> .prepare_fb = intel_prepare_plane_fb,
>>>> .cleanup_fb = intel_cleanup_plane_fb,
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_cdclk.c
>>>> b/drivers/gpu/drm/i915/display/intel_cdclk.c
>>>> index 43564295b864..42bd02638d32 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_cdclk.c
>>>> +++ b/drivers/gpu/drm/i915/display/intel_cdclk.c
>>>> @@ -2249,6 +2249,7 @@ static int intel_modeset_all_pipes(struct
>>>> intel_atomic_state *state)
>>>> */
>>>> for_each_intel_crtc(&dev_priv->drm, crtc) {
>>>> struct intel_crtc_state *crtc_state;
>>>> + struct intel_plane *plane;
>>>> int ret;
>>>>
>>>> crtc_state = intel_atomic_get_crtc_state(&state->base, crtc);
>>>> @@ -2266,12 +2267,14 @@ static int intel_modeset_all_pipes(struct
>>>> intel_atomic_state *state)
>>>> if (ret)
>>>> return ret;
>>>>
>>>> - ret = drm_atomic_add_affected_planes(&state->base,
>>>> - &crtc->base);
>>>> - if (ret)
>>>> - return ret;
>>>> -
>>>> - crtc_state->update_planes |= crtc_state->active_planes;
>>>> + for_each_intel_plane_on_crtc(&dev_priv->drm, crtc, plane) {
>>>> + struct intel_plane_state *plane_state =
>>>> + intel_atomic_get_plane_state_after_check(state,
>>>> +
>>>> crtc_state,
>>>> + plane);
>>>> + if (IS_ERR(plane_state))
>>>> + return PTR_ERR(plane_state);
>>>> + }
>>>> }
>>>>
>>>> return 0;
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_color.c
>>>> b/drivers/gpu/drm/i915/display/intel_color.c
>>>> index 9ab34902663e..1e3a623eaf82 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_color.c
>>>> +++ b/drivers/gpu/drm/i915/display/intel_color.c
>>>> @@ -1077,11 +1077,12 @@ intel_color_add_affected_planes(struct
>>>> intel_crtc_state *new_crtc_state)
>>>> if (!need_plane_update(plane, new_crtc_state))
>>>> continue;
>>>>
>>>> - plane_state = intel_atomic_get_plane_state(state, plane);
>>>> + plane_state =
>>>> + intel_atomic_get_plane_state_after_check(state,
>>>> + new_crtc_state,
>>>> + plane);
>>>> if (IS_ERR(plane_state))
>>>> return PTR_ERR(plane_state);
>>>> -
>>>> - new_crtc_state->update_planes |= BIT(plane->id);
>>>> }
>>>>
>>>> return 0;
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h
>>>> b/drivers/gpu/drm/i915/display/intel_display_types.h
>>>> index 976669f01a8c..526423437f63 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_display_types.h
>>>> +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
>>>> @@ -1541,4 +1541,10 @@ static inline u32 intel_plane_ggtt_offset(const
>>>> struct intel_plane_state *state)
>>>> return i915_ggtt_offset(state->vma);
>>>> }
>>>>
>>>> +/* intel_atomic_plane.c */
>>>> +struct intel_plane_state *
>>>> +intel_atomic_get_plane_state_after_check(struct intel_atomic_state *state,
>>>> + struct intel_crtc_state *crtc_state,
>>>> + struct intel_plane *plane);
>>>> +
>>>> #endif /* __INTEL_DISPLAY_TYPES_H__ */
>>>> diff --git a/drivers/gpu/drm/i915/intel_pm.c
>>>> b/drivers/gpu/drm/i915/intel_pm.c
>>>> index 53358e33df1b..5e6e54cb22fe 100644
>>>> --- a/drivers/gpu/drm/i915/intel_pm.c
>>>> +++ b/drivers/gpu/drm/i915/intel_pm.c
>>>> @@ -5242,11 +5242,12 @@ skl_ddb_add_affected_planes(const struct
>>>> intel_crtc_state *old_crtc_state,
>>>>
>>>> &new_crtc_state->wm.skl.plane_ddb_uv[plane_id]))
>>>> continue;
>>>>
>>>> - plane_state = intel_atomic_get_plane_state(state, plane);
>>>> + plane_state =
>>>> + intel_atomic_get_plane_state_after_check(state,
>>>> + new_crtc_state,
>>>> + plane);
>>>> if (IS_ERR(plane_state))
>>>> return PTR_ERR(plane_state);
>>>> -
>>>> - new_crtc_state->update_planes |= BIT(plane_id);
>>>> }
>>>>
>>>> return 0;
>>>> @@ -5534,11 +5535,12 @@ static int skl_wm_add_affected_planes(struct
>>>> intel_atomic_state *state,
>>>>
>>>> &new_crtc_state->wm.skl.optimal.planes[plane_id]))
>>>> continue;
>>>>
>>>> - plane_state = intel_atomic_get_plane_state(state, plane);
>>>> + plane_state =
>>>> + intel_atomic_get_plane_state_after_check(state,
>>>> + new_crtc_state,
>>>> + plane);
>>>> if (IS_ERR(plane_state))
>>>> return PTR_ERR(plane_state);
>>>> -
>>>> - new_crtc_state->update_planes |= BIT(plane_id);
>>>> }
>>>>
>>>> return 0;
>>>> --
>>>> 2.23.0
>>>>
>>>> _______________________________________________
>>>> Intel-gfx mailing list
>>>> Intel-gfx@lists.freedesktop.org
>>>> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
