Regards
Shashank
On 7/22/2017 12:34 AM, Imre Deak wrote:
On Fri, Jul 21, 2017 at 08:55:06PM +0530, Shashank Sharma wrote:
To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
blend mode to use the scaler in 5x3 ratio (bits 26 and 27)
This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.
V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
- Add readouts for state->ycbcr420 and 420 pixel_clock.
- Handle warning due to mismatch in clock for ycbcr420 clock.
- Rename PIPEMISC macros to match the Bspec.
- Add a debug print stating if YCBCR 4:2:0 output enabled.
Added r-b from Ville
V9: Addressed review comments from Imre:
- Add 420 mode clock adjustment in intel_hdmi_mode_valid to
prevent 420_only modes getting rejected for high clock.
- Add port clock adjustment for ycbcr420 modes in ddi_get_clock
- Rename macros as per Ville's suggestion.
- Remove unnecessary wl changes.
V10: Added r-b from Imre
Cc: Ville Syrjala <[email protected]>
Cc: Ander Conselvan de Oliveira <[email protected]>
Cc: Daniel Vetter <[email protected]>
Cc: Imre Deak <[email protected]>
Reviewed-by: Ander Conselvan de Oliveira <[email protected]>
Reviewed-by: Ville Syrjala <[email protected]>
Reviewed-by: Imre Deak <[email protected]>
Signed-off-by: Shashank Sharma <[email protected]>
---
drivers/gpu/drm/i915/i915_reg.h | 3 +++
drivers/gpu/drm/i915/intel_ddi.c | 3 +++
drivers/gpu/drm/i915/intel_display.c | 14 ++++++++++++++
drivers/gpu/drm/i915/intel_hdmi.c | 3 +++
4 files changed, 23 insertions(+)
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index c712d01..e5b4e2f 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -5227,6 +5227,9 @@ enum {
#define _PIPE_MISC_A 0x70030
#define _PIPE_MISC_B 0x71030
+#define PIPEMISC_YUV420_ENABLE (1<<27)
+#define PIPEMISC_YUV420_MODE_FULL_BLEND (1<<26)
+#define PIPEMISC_OUTPUT_COLORSPACE_YUV (1<<11)
#define PIPEMISC_DITHER_BPC_MASK (7<<5)
#define PIPEMISC_DITHER_8_BPC (0<<5)
#define PIPEMISC_DITHER_10_BPC (1<<5)
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index efb1358..d88731b 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -1174,6 +1174,9 @@ static void ddi_dotclock_get(struct intel_crtc_state
*pipe_config)
else
dotclock = pipe_config->port_clock;
+ if (pipe_config->ycbcr420)
+ dotclock = pipe_config->port_clock / 2;
I see, it's Friday afternoon, so who cares about some statecheck WARNs
in dmesg?;) It's '* 2'. Moreover it'd be incorrect for YUV420 12bpc, so
just
dotclock *= 2;
Embarrassing, let me too blame it to Friday evening ;-), but I
seriously looked for warnings in dmesg.
Let me check it on Monday, why dint I get it in dmesg and come back !
+
if (pipe_config->pixel_multiplier)
dotclock /= pipe_config->pixel_multiplier;
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 05ba0e9..6473ecf 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -8034,6 +8034,7 @@ static void haswell_set_pipemisc(struct drm_crtc *crtc)
{
struct drm_i915_private *dev_priv = to_i915(crtc->dev);
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_crtc_state *config = intel_crtc->config;
if (IS_BROADWELL(dev_priv) || INTEL_INFO(dev_priv)->gen >= 9) {
u32 val = 0;
@@ -8059,6 +8060,12 @@ static void haswell_set_pipemisc(struct drm_crtc *crtc)
if (intel_crtc->config->dither)
val |= PIPEMISC_DITHER_ENABLE | PIPEMISC_DITHER_TYPE_SP;
+ if (config->ycbcr420) {
+ val |= PIPEMISC_OUTPUT_COLORSPACE_YUV |
+ PIPEMISC_YUV420_ENABLE |
+ PIPEMISC_YUV420_MODE_FULL_BLEND;
+ }
+
I915_WRITE(PIPEMISC(intel_crtc->pipe), val);
}
}
@@ -9128,6 +9135,10 @@ static bool haswell_get_pipe_config(struct intel_crtc
*crtc,
pipe_config->scaler_state.scaler_users &= ~(1 <<
SKL_CRTC_INDEX);
}
+ if (IS_GEMINILAKE(dev_priv))
+ pipe_config->ycbcr420 = I915_READ(PIPEMISC(crtc->pipe)) &
+ PIPEMISC_YUV420_ENABLE;
You missed my last comments about this part (it was a separate email
from the rest of my comments).
Yes, sorry about that, will get it done !
- Shashank
+
power_domain = POWER_DOMAIN_PIPE_PANEL_FITTER(crtc->pipe);
if (intel_display_power_get_if_enabled(dev_priv, power_domain)) {
power_domain_mask |= BIT_ULL(power_domain);
@@ -10731,6 +10742,9 @@ static void intel_dump_pipe_config(struct intel_crtc
*crtc,
pipe_config->fdi_lanes,
&pipe_config->fdi_m_n);
+ if (pipe_config->ycbcr420)
+ DRM_DEBUG_KMS("YCbCr 4:2:0 output enabled\n");
+
if (intel_crtc_has_dp_encoder(pipe_config)) {
intel_dump_m_n_config(pipe_config, "dp m_n",
pipe_config->lane_count, &pipe_config->dp_m_n);
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c
b/drivers/gpu/drm/i915/intel_hdmi.c
index 6addef5..da9d1d3 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -1295,6 +1295,9 @@ intel_hdmi_mode_valid(struct drm_connector *connector,
if (mode->flags & DRM_MODE_FLAG_DBLCLK)
clock *= 2;
+ if (drm_mode_is_420_only(&connector->display_info, mode))
+ clock /= 2;
+
/* check if we can do 8bpc */
status = hdmi_port_clock_valid(hdmi, clock, true, force_dvi);
--
2.7.4
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
