On Thu, Apr 06, 2017 at 12:15:36PM -0700, Rodrigo Vivi wrote:
> From: Clint Taylor <clinton.a.tay...@intel.com>
>
> vswing programming sequence step 2 requires the Loadgen_select bit to
> be set in PORT_TX_DW4 lane reigsters per table defined by Bit rate and
> lane width. Implemented the change that was marked as FIXME in the
> driver.
>
> v2: (Rodrigo) checkpatch fixes.
>
> Signed-off-by: Clint Taylor <clinton.a.tay...@intel.com>
> Signed-off-by: Rodrigo Vivi <rodrigo.v...@intel.com>
> ---
> drivers/gpu/drm/i915/intel_ddi.c | 38 ++++++++++++++++++++++++++++++++------
> 1 file changed, 32 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c
> b/drivers/gpu/drm/i915/intel_ddi.c
> index a4d7061..3f461c3 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -1846,10 +1846,24 @@ static void cnl_ddi_vswing_program(struct
> drm_i915_private *dev_priv,
> I915_WRITE(CNL_PORT_TX_DW7_GRP(port), val);
> }
>
> -static void cnl_ddi_vswing_sequence(struct drm_i915_private *dev_priv,
> - u32 level, enum port port, int type)
> +static void cnl_ddi_vswing_sequence(struct intel_encoder *encoder, u32 level)
This change looks unrelated. And it reminds me that I should resurrect
my remaining encoder->type fixings...
> {
> + struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> + struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
> + enum port port = intel_ddi_get_encoder_port(encoder);
> + int type = encoder->type;
> + int width = 0;
> + int rate = 0;
> u32 val;
> + int ln = 0;
> +
> + if ((intel_dp) && (type == INTEL_OUTPUT_EDP || type ==
> INTEL_OUTPUT_DP)) {
intel_dp isn't needed outside this branch, so the declaration could be
moved here.
> + width = intel_dp->lane_count;
> + rate = intel_dp->link_rate;
> + } else {
> + width = 4;
> + /* Rate is always < than 6GHz for HDMI */
> + }
>
> /*
> * 1. If port type is eDP or DP,
> @@ -1865,8 +1879,21 @@ static void cnl_ddi_vswing_sequence(struct
> drm_i915_private *dev_priv,
>
> /* 2. Program loadgen select */
> /*
> - * FIXME: Program PORT_TX_DW4_LN depending on Bit rate and used lanes
> + * Program PORT_TX_DW4_LN depending on Bit rate and used lanes
> + * <= 6 GHz and 4 lanes (LN0=0, LN1=1, LN2=1, LN3=1)
> + * <= 6 GHz and 1,2 lanes (LN0=0, LN1=1, LN2=1, LN3=0)
> + * > 6 GHz (LN0=0, LN1=0, LN2=0, LN3=0)
> */
> + for (ln = 0; ln <= 3; ln++) {
< 4 would look more typical.
> + val = I915_READ(CNL_PORT_TX_DW4_LN(port, ln));
> + val &= ~LOADGEN_SELECT;
> +
> + if (((rate < 600000) && (width == 4) && (ln >= 1)) ||
> + ((rate < 600000) && (width < 4) && ((ln == 1) || (ln ==
> 2)))) {
< looks wrong based on the comment. Should be <=
Looks lispy. Could trim some of the parens.
> + val |= LOADGEN_SELECT;
> + }
> + I915_WRITE(CNL_PORT_TX_DW4_LN(port, ln), val);
> + }
>
> /* 3. Set PORT_CL_DW5 SUS Clock Config to 11b */
> val = I915_READ(CNL_PORT_CL1CM_DW5);
> @@ -1920,7 +1947,7 @@ uint32_t ddi_signal_levels(struct intel_dp *intel_dp)
> else if (IS_GEN9_LP(dev_priv))
> bxt_ddi_vswing_sequence(dev_priv, level, port, encoder->type);
> else if (IS_CANNONLAKE(dev_priv)) {
> - cnl_ddi_vswing_sequence(dev_priv, level, port, encoder->type);
> + cnl_ddi_vswing_sequence(encoder, level);
> /* DDI_BUF_CTL bits 27:24 are reserved on CNL */
> return 0;
> }
> @@ -2022,8 +2049,7 @@ static void intel_ddi_pre_enable_hdmi(struct
> intel_encoder *encoder,
> bxt_ddi_vswing_sequence(dev_priv, level, port,
> INTEL_OUTPUT_HDMI);
> else if (IS_CANNONLAKE(dev_priv))
> - cnl_ddi_vswing_sequence(dev_priv, level, port,
> - INTEL_OUTPUT_HDMI);
> + cnl_ddi_vswing_sequence(encoder, level);
>
> intel_hdmi->set_infoframes(drm_encoder,
> has_hdmi_sink,
> --
> 1.9.1
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
