If you really want/need them, search for a reverse assembler. I think there is one on the CBT tape.
-----Original Message----- From: IBM Mainframe Discussion List <IBM-MAIN@LISTSERV.UA.EDU> On Behalf Of Peter Sent: Thursday, May 9, 2019 2:43 PM To: IBM-MAIN@LISTSERV.UA.EDU Subject: Re: Assembly JCL for tpx 5.4 [External Email] It's not part of smpe.. Just assembly and Linkedit.. On Thu, 9 May, 2019, 10:35 PM Jousma, David, < 000001a0403c5dc1-dmarc-requ...@listserv.ua.edu> wrote: > Probably not a good idea. Do you know if they were smpe installed? There > could be a copy in your SMPPTS, or SMPSTS datasets? Otherwise, try it, > but I'd expect unexpected results. > > > ______________________________________________________________________ > _______________________________ > Dave Jousma > AVP | Manager, Systems Engineering > > Fifth Third Bank | 1830 East Paris Ave, SE | MD RSCB2H | Grand > Rapids, MI 49546 > 616.653.8429 | fax: 616.653.2717 > > > -----Original Message----- > From: IBM Mainframe Discussion List <IBM-MAIN@LISTSERV.UA.EDU> On > Behalf Of Peter > Sent: Thursday, May 9, 2019 2:24 PM > To: IBM-MAIN@LISTSERV.UA.EDU > Subject: Re: Assembly JCL for tpx 5.4 > > **CAUTION EXTERNAL EMAIL** > > **DO NOT open attachments or click on links from unknown senders or > unexpected emails** > > We have some user exits used for TPX 5.2 and unfortunately we don't > know where the source codes are located. > > Is it ok to just copy over to 5.4 ? > > On Fri, 3 May, 2019, 3:09 AM Mark Zelden, <m...@mzelden.com> wrote: > > > On Thu, 2 May 2019 15:44:14 -0500, Michael Cleary < > > michaeljosephcle...@yahoo.com> wrote: > > > > >If the product is installed with SMPE best practice would be to > > >install > > the exit via an SMPE USERMOD. > > > > > > > Not a bad idea, but I don't consider that necessary if the product > > doesn't come with an LMOD for that exit in the product loadlib that > > is being replaced by the one you want to create. There is no chance > > that product maintenance will regress the exit which is the main > > reason you would want a usermod. Good product installation > > documentation that says there is an exit in use and putting it in a > > concatenated loadlib or even directly into the product loadlib is > > fine as far as I'm concerned. Just so the next pour sole that has > > to upgrade the product next knows there is an exit and where the > > source code and asm/lnk JCL is. > > > > But that's just my opinion. Creating the usermod is more trouble > > than I want to go through if I don't have to do it to protect the > > integrity of the product installation. > > > > Best Regards, > > > > Mark > > -- > > Mark Zelden - Zelden Consulting Services - z/OS, OS/390 and MVS ITIL > > v3 Foundation Certified mailto:m...@mzelden.com Mark's MVS Utilities: > > https://protect2.fireeye.com/url?k=146e0b62-4832ff6d-146e21fa-0cc47a > > 33 347c-65139aa7751c56b9&u=http://www.mzelden.com/mvsutil.html > > Systems Programming expert at > > http://search390.techtarget.com/ateExperts/ > > -------------------------------------------------------------------- > > -- For IBM-MAIN subscribe / signoff / archive access instructions, > > send email to lists...@listserv.ua.edu with the message: INFO > > IBM-MAIN > > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send > email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN > **CAUTION EXTERNAL EMAIL** > > **DO NOT open attachments or click on links from unknown senders or > unexpected emails** > > This e-mail transmission contains information that is confidential and may > be privileged. It is intended only for the addressee(s) named above. If > you receive this e-mail in error, please do not read, copy or > disseminate it in any manner. If you are not the intended recipient, > any disclosure, copying, distribution or use of the contents of this > information is prohibited. Please reply to the message immediately by > informing the sender that the message was misdirected. After replying, > please erase it from your computer system. Your assistance in correcting this > error is appreciated. > > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send > email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN > ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN FIRST TENNESSEE Confidentiality notice: This e-mail message, including any attachments, may contain legally privileged and/or confidential information. If you are not the intended recipient(s), or the employee or agent responsible for delivery of this message to the intended recipient(s), you are hereby notified that any dissemination, distribution, or copying of this e-mail message is strictly prohibited. If you have received this message in error, please immediately notify the sender and delete this e-mail message from your computer. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
