14F


Explanation



During processing of a STATUS macro, the system found an error.

Register 15 contains a hexadecimal reason code that explains the error:

Code

   Explanation



04

     The STATUS macro specified an incorrect function code. Register 2

     contains the function code.



08

     Only a program in supervisor state with PSW key 0-7 can request the

     specified STATUS function.



0C

     You specified an address space identifier (ASID) for the STATUS STOP

     function. The ASID parameter is valid only on the STATUS START
function.


10

     You issued the STATUS macro with the must complete (MC) parameter, but

     you had already specified the MC parameter on a previous invocation.
You
     must issue the STATUS macro with the RESET,MC,STEP parameter before

     issuing another SET,MC,STEP.



14

     You issued a STATUS macro with the STOP option, but you had already

     issued a STATUS STOP. You must issue the STATUS macro with the START

     option before issuing another STATUS STOP.



18

     The input mask you specified on the STATUS SET,SD invocation set

     TCBSTPP. This bit can only be set by specifying STATUS STOP.



1C

     The mask you specified on the STATUS SET,ND invocation set TCBSTP.
This
     bit can only be set by specifying STATUS SET,MC or STATUS SET,MC,STEP.



20

     A routine running under a service request block (SRB) cannot use a

     STATUS macro to set a step nondispatchable.



24

     In the parameter list on a SET or RESET request, the caller specified
an
     incorrect address for a task control block (TCB).



28

     The caller does not hold a needed local lock.



2C

     The caller does not hold a needed local lock.



30

     The specified TCB did not pass an acronym check. The TCB was probably

     overlaid or incorrect.



34

     The mask of nondispatchability bits specified with the SD parameter

     includes the TCBSRBND bit. This nondispatchability bit can be set only

     by specifying STATUS STOP,SRB.



38

     The STATUS macro specified an incorrect function code.



3C

     A program issuing either STATUS SET,MC,PROCESS or STATUS

     RESET,MC,PROCESS was not running in task mode. The calling program
must
     be running in task mode.



44

     The input mask you specified on the STATUS SET,ND invocation, set the

     TCBPNDSP bit. The caller cannot set TCBPNDSP.



48

     A routine running under a service request block (SRB) cannot use a

     STATUS macro for the requested function.



4C

     You specified an input address space identifier (ASID) or enclave
token
     on a STATUS invocation that is not valid.



50

     The input TCB specified on a STATUS STOP or STATUS START invocation
was
     the caller's TCB. The caller cannot perform this operation on itself.



54

     A STATUS invocation to set a caller's nondispatchability bit was
invoked
     using SVC.



58

     STATUS STOP,SRB was invoked, but had been invoked previously. Invoke

     STATUS START,SRB before invoking STATUS STOP,SRB again.



5C

     The system detected a possible overlay of a TCB field for a task that
is
     the target of a STATUS macro request.



60
     The input TCB specified on a STATUS SET,ND,E or STATUS SET,SD,E

     invocation was the caller's TCB. The caller cannot perform this

     operation on itself.



System action

The system abnormally ends the program that issued the STATUS macro.



System programmer response



If the error recurs and the program is not in error, look at the messages
in
the job log for more information. Search problem reporting data bases for a

fix for the problem. If no fix exists, contact the IBM Support Center.

Provide the program listing for the job.



Programmer response



Correct the error. Run the job again.



Source

Task management


Ramsey

On Wed, Sep 9, 2026 at 2:03 AM Brian Westerman <
[email protected]> wrote:

> S14F -      THE ROUTINE ATTEMPTED TO EXECUTE THE STATUS MACRO INSTRUCTION
>             FOR OTHER THAN THE STOP, STOP SYNCH, OR START FUNCTION AND WAS
> NOT
>             IN SUPERVISOR KEY (0-7).
>
> ----------------------------------------------------------------------
> For IBM-MAIN subscribe / signoff / archive access instructions,
> send email to [email protected] with the message: INFO IBM-MAIN
>

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to [email protected] with the message: INFO IBM-MAIN

Reply via email to