Thank you.
I forgot to mention that I did run this with TYPRUN=SCAN and get
the same message.
And to be sure, I have been running this JOB off an for the past
month.
I have gotten file not found. That was the first thing I checked,
using "F FOUND" and that typically shows me the missing DSN.
Not on/with this failure.
And submitting it again -- the suffixing number of the error is
different, and is greater than the number of JCL statements in
this JOB. So that doesn't seem related.
Regards,
Steve Thompson
On 4/22/2025 5:01 PM, Ramsey Hallman wrote:
The version prior to 3.1 is 2.5 of z/OS.
>From the error message, it does not necessarily have to be the job name. It
could be other JCL issues.
IEFC452I text - JOB NOT RUN - JCL ERROR
Explanation
Depending on the message text, one of the following:
JOBFAIL
The error was detected on a JOB statement and the job name is not
known.
INVALID
The system detected an error in a JOB or other JCL statement, and
the job name (the label on the JOB statement) is invalid.
jobname
The system detected an error in a JCL statement, or the job was
cancelled while on the input queue.
procstep
The procedure was specified in the first operand of a START command.
In this case, either the procedure was not found in SYS1.PROCLIB or,
if found, the procedure had an error in a JCL statement. Message
IEE122I or IEE132I will always follow this message.
The error message appears in the SYSOUT data set.
This message can also be issued for various environmental errors,
such as an error occurring while trying to read a record from the
JCL text data set or an I/O error occurring while trying to get
procedure statements.
System action
If the operator cancelled the job, all steps of the job, beginning
with the step currently being processed, will be ended. Otherwise,
the job will not be initiated; no steps will be processed. If
procstep appears, the START command will not be run.
Operator response
If the job name appears, none. If procstep appears, either reenter
the START command with the correct procedure name, or, if the
procedure name is correct, notify the application programmer.
Programmer response
Check the procedure for errors.
Source
Converter
Module
IEFCNJRT
Routing code
2,10
Descriptor code
4
On Tue, Apr 22, 2025 at 3:53 PM Steve Thompson <ste...@wkyr.net> wrote:
Hi all, got a weird one.
I am running the same JOB over and over processing different
files. All that changes is the suffix on an output DSN that
identifies the DATA cycle of this execution, and the SORTIN
DD/DSN contents (some have a single file some have up to 15
files). Data may be on disk or tape. TPM holds the job until HSM
restore completes if that is why the data is on tape.
I would love to show you the JCL, but I am NOT allowed. Suffice
to say security controls.
I have taken the JOB cards off another one of these JOBs that ran
successfully and replaced the JOB card (one from a prior
submission of this specific JOB).
And I still get this error. The last thing it says is 748.
Since I don't have 700 JCL statements, that isn't the problem.
Besides this is supposedly a JOB card error!!
BTW, sometimes the files I have been told to pick disappear
before I can get the JCL updated and submitted, so I do get file
not found errors. But this is not the issue here.
I have a copy of the full tech library for the Version of z/OS
just prior to 3.1 (can't remember the V/R). And it is not helping
me with this.
--
Thanks for your help/insight in advance.
Steve Thompson
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to lists...@listserv.ua.edu with the message: INFO IBM-MAIN
