yes it does. I think I'll keep this functionality. On Wed, Jun 6, 2012 at 12:09 PM, Robin Atwood <[email protected]>wrote:
> Now if you set PF8 to K D,F and PF12 to K E,D, it all becomes very > familiar! > > HTH > -Robin > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Matan Cohen > Sent: 06 June 2012 16:18 > To: [email protected] > Subject: Re: Consoles New options > > > Just found the 'K D,F' which scroll the status display to the next > frame. > > On Wed, Jun 6, 2012 at 11:15 AM, Matan Cohen > <[email protected]>wrote: > > > P.S > > there is the 'K E,D" which delete all of the status display . > > > > On Wed, Jun 6, 2012 at 11:09 AM, Matan Cohen > <[email protected]>wrote: > > > >> thanks for the help . > >> Linda - you are right , I do have the control area set. > >> I checked out the CONTROL command in the manuals and couldn't found > >> how can i control this display in meaning of scrolling \ deletion of > > >> this mesages . I'll probably will set the AREA(10) to AREA(NONE) in > my CONSOLxx . > >> > >> thanks. > >> > >> > >> On Wed, Jun 6, 2012 at 4:10 AM, Linda Mooney > <[email protected]>wrote: > >> > >>> Hi Matan, > >>> > >>> > >>> It sounds like your console has a control area set for it. Control > >>> areas can be set up in parmlib, or by command, usually at the > >>> console itself (can be done at another console). To confirm, enter K > > >>> A,REF at the console. The system will respond with the size of the > >>> control area, if one has been set. To remove a control area enter K > A,NONE at the console. > >>> Your z/OS Commands manual will have more info. Check also in the > >>> CONSOLxx member of parmlib for the AREA statement. Many shops set > the AREA to none. > >>> > >>> > >>> > >>> HTH, > >>> > >>> > >>> > >>> Linda > >>> > >>> > >>> ----- Original Message ----- > >>> > >>> > >>> From: "Matan Cohen" <[email protected]> > >>> To: [email protected] > >>> Sent: Monday, June 4, 2012 11:56:11 PM > >>> Subject: Consoles New options > >>> > >>> Hi, > >>> I notice that since z/OS 1.10 (maybe even from an earlier releases) > > >>> the Consoles was a little bit diffrent. > >>> one of the Major diffrent is regarding the response messages . when > >>> i'm entering a console command the response message is appearing in > >>> the bottom of the console messages and doesn't scroll up as other > >>> messages. > >>> can some one point me to a document describing this options and How > > >>> can i control them . > >>> > >>> -- > >>> ______________________ > >>> best regards, > >>> matan cohen > >>> MF System Administrator. > >>> > >>> -------------------------------------------------------------------- > >>> -- For IBM-MAIN subscribe / signoff / archive access instructions, > >>> send email to [email protected] with the message: INFO IBM-MAIN > >>> > >>> -------------------------------------------------------------------- > >>> -- For IBM-MAIN subscribe / signoff / archive access instructions, > >>> send email to [email protected] with the message: INFO IBM-MAIN > >>> > >> > >> > >> > >> -- > >> ______________________ > >> best regards, > >> matan cohen > >> MF System Administrator. > >> > >> > > > > > > -- > > ______________________ > > best regards, > > matan cohen > > MF System Administrator. > > > > > > > -- > ______________________ > best regards, > matan cohen > MF System Administrator. > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, send > email to [email protected] with the message: INFO IBM-MAIN > > This message has been scanned by MailController - > portal1.mailcontroller.co.uk > > ---------------------------------------------------------------------- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: INFO IBM-MAIN > -- ______________________ best regards, matan cohen MF System Administrator. ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: INFO IBM-MAIN
