Please contact your local CPWR support centre to inquiry about this issue. On the web its frontline.compuware.com
In north america its 1.800.538.7822 The contents of this e-mail are intended for the named addressee only. It contains information that may be confidential. Unless you are the named addressee or an authorized designee, you may not copy or use it, or disclose it to anyone else. If you received it in error please notify us immediately and then destroy it. From: IBM Mainframe Discussion List <[email protected]> To: [email protected] <[email protected]> Sent: Mon Mar 07 03:32:59 2011 Subject: S001-03 System Abend Code - FILEAID Batch ABEND *Hello - * ** We recently had a job-abend in our *Production Environment*. The job runs FILEAID in Batch, to *Filter* *out* Records, based on the *//SYSIN Control Card*. Here's the step. //FILEVIS EXEC PGM=*FILEAID* //DD01 DD DSN=CP81.CPARS.GRAP222.DATA,DISP=SHR //DD01O DD DSN=CP81.CPARS.GRAP222.DATA,DISP=SHR //SYSIN DD DSN=CP81.CPARS.PARMFILE.DATA(SELVIST),DISP=SHR *FILEAID *Abended with a Return-Code 12. The Job Log, showed the following*IEC020I * messages. IEC020I *001-3*,CPARS22A,FILEVIS,DD01,3189,SMA3T2, IEC020I CP81.CPARS.GRAP222.DATA IEC020I NON-ACCEPTABLE ERROR When I looked up the *System Abend Code S001, Return Code 03*, in the IBM MVS Messages Manual, I found the following explanation : "If the return code is 3, for QSAM, *an unacceptable error occurred* because of one of the following: – The caller returned from the SYNAD. – The caller did not provide a SYNAD. Look at the input/output block (IOB) to determine why the error was unacceptable to QSAM. " When I searched for SYNAD, I found that, SYNAD is an *Error-Analysis routine *. You must supply it. *File-Aid Messages* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * AN ABEND HAS OCCURRED: S001 U0000 * * * * * * * * PSW: 078D1000 00DD2644 RELEASE: 9.2.0 02/07/2010 * * * * * * * * LOCATION: *IGG019AQ*+000000BA EP=00DD2588 * * * * * * * * R0 000068D0 R1 000DABC0 R2 80065E2C R3 00000000 * * * * * * * * R4 00007B38 R5 80006FFE R6 000DABC0 R7 00000000 * * * * * * * * R8 000B0900 R9 00066DF0 RA 00035800 RB 000716D2 * * * * * * * * RC 00036800 RD 0003A310 RE 00DD2636 RF 0004DEF0 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * QSAM GET I/O ERROR "NO RECORD FOUND" ON DD01-SMA3T2 DS BLOCK CCHHR=0047000203! BLKS-SKIPPED=25,RECORDS-READ=2065,COPIED=2065 2,065 RECORDS WRITTEN TO DD01O-CP81.CPARS.GRAP222.DATA VOL=SMA3T2 ** After trying to *re-run* this step in *Production*, it ran fine, and completed Successfully. *My Understanding* My understanding is *File-Aid* in turn CALLS Qsam Routines - like *IGG019**to access the records from the QSAM File, Blocking and Unblocking. Due to an error, some Blocks were skipped by QSAM while fetching the data, into its * Buffers*. *My Questions* 1. How do I access the QSAM Input Output Block, as suggested in the IBM Manual? 2. How do I interprete the PSW, and Register 0-15 contents? 3. What is the exact cause of this abend according to you? Eagerly awaiting your reply. Thank you very much, Quasar S. Chunawala ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
