HCD 2 -> 11 then / on the processor line and then option 1 allows control of the IOCDS's. No need to access the HMC
Jerry Whitteridge Design Engineer Safeway Inc. 925 951 4184 If you feel in control you just aren't going fast enough. > -----Original Message----- > From: IBM Mainframe Discussion List [mailto:[email protected]] On > Behalf Of Mike Myers > Sent: Wednesday, February 09, 2011 10:21 AM > To: [email protected] > Subject: Re: HCD Write Error > > Matt: > > You must perform this from the Service Element or logon to the > service > element from the HMC. > > Go to Groups and select Defined CPCs. > > Right click the desired CPC's icon, select Recovery and then Single > Object Operations from the pull down lists (this assumes you are > using > the HMC in compatibility mode and have the HMC code that is the > Linux > version). > > Once logged onto the SE, right click the CPC icon, then select CPC > Configuration and then Input/Output (I/O) Configuration from the > pull > down lists. > > The resulting screen will show you the IOCDS files. Select the one > you > want to unprotect and and change it's write-protected status. Then > you > can rerun your IOCDS generation and the IOCDS will be updated. You > may > want to repeat the process and protect your new IOCDS. > > Mike Myers > Mentor Services Corporation > > On 2/9/2011 11:56 AM, Dazzo, Matt wrote: > > Working in HCD and looking to 'Build IOCDS' to be used for the > next ipl. The build ends with the 'write protect' error below. > According to the IOCP message guide it states; > > > > ' ICP408I IOCDS Ax IS WRITE PROTECTED Explanation: IOCP > attempted to write an IOCDS to the support element hard disk but the > IOCDS is write-protected. System action: IOCP ends the write > operation. Programmer response: Remove the write protection and > rerun the job. To remove the write protection, use Disable Write > Protection under Options on the Input/Output Configuration panel.' > > > > First I do not see any 'disable write protection' option in the > hcd panels as stated above in the iocp guide, second I was able to > build a new IOCDS back in Dec to A0 with no problems. I have > exhausted the iocp guide and the hcd guide and did find the > specifics to disable write protection, although it was mentioned in > the hcd options I'm just not see it. > > > > > > HDC outout listing error; > > ICP408I IOCDS A1 IS WRITE PROTECTED > > ICP058I IOCP DID NOT WRITE IOCDS A1 > > ICP051I IOCP VERSION 02.02.00 TERMINATED. CODE=41 > > > > CBD.CPC.IOCDS - my userid has update auth to this profile. > > > > How do I disable the write protection? Tks Matt > > > > > > > > > > ------------------------------------------------------------------ > ---- > > For IBM-MAIN subscribe / signoff / archive access instructions, > > send email to [email protected] with the message: GET IBM-MAIN > INFO > > Search the archives at http://bama.ua.edu/archives/ibm-main.html > > > > -------------------------------------------------------------------- > -- > For IBM-MAIN subscribe / signoff / archive access instructions, > send email to [email protected] with the message: GET IBM-MAIN > INFO > Search the archives at http://bama.ua.edu/archives/ibm-main.html "Email Firewall" made the following annotations. ------------------------------------------------------------------------------ Warning: All e-mail sent to this address will be received by the corporate e-mail system, and is subject to archival and review by someone other than the recipient. This e-mail may contain proprietary information and is intended only for the use of the intended recipient(s). If the reader of this message is not the intended recipient(s), you are notified that you have received this message in error and that any review, dissemination, distribution or copying of this message is strictly prohibited. If you have received this message in error, please notify the sender immediately. ============================================================================== ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [email protected] with the message: GET IBM-MAIN INFO Search the archives at http://bama.ua.edu/archives/ibm-main.html
