Thank you. I tried loading it and then doing an optimization and just get "Field of View must be positive". The FOV has positive values in it, so I'm not sure what it's upset about. On Mon, 2021-12-27 at 10:43 -0800, [email protected] wrote: > I was curious enough (after not seeing a reply to your attached .pto > file from Bruno, to look up something I'd seen before but > forgotten.In the documentation of "i" lines in the .pto file it says: > > # Parameters in different images can be linked using '=' > # followed by the image number starting with 0. > # Example 'v=0' sets horizontal field of view as in# image > number 0. This feature works for the variables# v, a, b, c, (r, > p, y with caution) d, e, g, and t > In your .pto file, each image other than the anchor has a line like: > i w4608 h3456 f0 v=0 Ra=0 Rb=0 Rc=0 Rd=0 Re=0 Eev3.85299770079307 Er1 > Eb1 r=0 p=0 y=0 TrX=0 TrY=0 TrZ=0 Tpy=0 Tpp=0 j0 a=0 b=0 c=0 d=0 e=0 > g=0 t=0 Va=0 Vb=0 Vc=0 Vd=0 Vx=0 Vy=0 Vm5 n"IMG_20210728_114219.jpg" > > > All those = in that line force every parameter to match the > parameters of the anchor image, so optimize can't optimize anything. > Inside Hugin, I don't know how to undo all that. In a text editor, > it is trivial to undo (global replace of =0 with 0 in the section > holding all the i lines. I don't know if the result of that is > correct enough to get you back on track. But I'll attach it in case > it helps. > On Monday, December 27, 2021 at 10:22:19 AM UTC-5 Jon Schewe wrote: > > On Mon, 2021-12-27 at 14:52 +0000, Bruno Postle wrote: > > > On Mon, 27 Dec 2021, 12:47 Jon Schewe, wrote: > > > > With a small experiment I managed to get into this state by > > > > telling Hugin to optimize X, Y, Z only for the images. It ran > > > > the optimize and told me that the average distance between all > > > > control points was zero. At this point the project appears to > > > > be in an unusable state. > > > > > > Maybe attach a PTO project (no need for the images), it may be > > > obvious what the problem is. > > > > Attached. > > > > > > > > > > -- > > A list of frequently asked questions is available at: > http://wiki.panotools.org/Hugin_FAQ > > --- > > You received this message because you are subscribed to the Google > Groups "hugin and other free panoramic software" group. > > To unsubscribe from this group and stop receiving emails from it, > send an email to [email protected]. > > To view this discussion on the web visit > https://groups.google.com/d/msgid/hugin-ptx/81dd2308-3a0a-4aaf-aa82-6add529fef36n%40googlegroups.com > . >
-- A list of frequently asked questions is available at: http://wiki.panotools.org/Hugin_FAQ --- You received this message because you are subscribed to the Google Groups "hugin and other free panoramic software" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/hugin-ptx/1f69436d157b63bbd9df2618075874b84ea9df59.camel%40mtu.net.
