Hello!
Thanx.
The problem the stacking was: the hugin created only 23 stacks, after I
change the stack size to 1, the result is much better.
btw, I dont have Optimalize tab. Its greyed out, as the Exposure tab.
thanx again
Csaba
On 2021-04-06 07:57, Gunter Königsmann wrote:
A good strategy might be first adding a few (4 per image pair) control
points that tell hugin which window is which, then aligning
preliminarily and telling hugin only then to add its 20 additional
control points. One or two of then will be in the wrong place, again.
But there is the "clean up control points" option for that.
Kind regards,
Gunter.
Am 5. April 2021 16:47:48 MESZ schrieb "Luís Henrique Camargo Quiroz"
<[email protected]>:
Hi Csaba!
Just an idea: maybe you are using the "simple" interface, and
this creates or tries to create new CP pairs before new alignment
of (new) images? I am not sure, because I don't use this
interface; I think it is intended for beginners and aiming to
create a panorama "at once" from a given set of photos. And of
course in your case you are feeding and growing an initial set of
photos (your # 3) , and starting a recipe meant to be run just
once when you press align (#1) and this starts with "create CPs".
I advise you to try at least the advanced interface. In this
case you will "align" only when you /optimize/ the panorama
parameters, and this process does /not/ create new CPs. You will
have to create the CPs beforehand, and you can improve or create
yourself new CPs when desidered -- and they will take effect after
a subsequent optimization. A rule of thumb is optimization of
'positions only', and when the result seemed OK (or almost), then
you could include 'positions and visualization', etc. For a
correct 'visualization' optimization the panorama must be a
complete turn around, and this is the case with your cylindricals.
As for the stacks, I think some photos could have an excessive
superposition and/or the same kind of image content and this could
fool Hugin.
Try please the advanced interface and tell us your progress.
Goof luck!
regards,
Luis Henrique
Em seg., 5 de abr. de 2021 às 06:04, Csaba Tóth
<[email protected] <mailto:[email protected]>>
escreveu:
Hello!
My problems are:
I have a large (100+) photo set for cylindrical projection.
(for the whole rendering take 12+ hour)
1. If I use the align button, it will always create new
contol points. An because the image contains many block
house always create point between wrong pairs. If I fix
this, I cant preview it, because it say "need to align
again". If I do, it will mess up again (and I need to
check every 100+ image to searching the wrong pairs, It
will be better to display a matrix, every cell how many cp
for that pair)
2. there are "stacks" in the result: many images in the same
place, same orientation, and I dont know why, and how
handle it.
3. If I start with few images and add more, (and "align" it
to see the result) I get error: there are two not linked
group [0],[1-9] If i fix it, add new one, get more not
linked groups: [0],[1],[2-10], and begin mess up (start
rotate the first image)
How can I "align" the images to see the result without the
"align" button, or without the messing up?
what I want to do:
1. load every image, "align" it to see where need to fix.
2. fix an error (add/remove cp-s, try to rotate, add
horizontal lines etc)
3. preview the result, if there is error: -> 2
4. straigthen
5. define the crop
6. create the panorama
Thanx
Csabastacks.png
(there is two stacks each with 10+ image, the same place, same
orientation)
--
A list of frequently asked questions is available at:
http://wiki.panotools.org/Hugin_FAQ
<http://wiki.panotools.org/Hugin_FAQ>
---
You received this message because you are subscribed to the
Google Groups "hugin and other free panoramic software" group.
To unsubscribe from this group and stop receiving emails from
it, send an email to [email protected]
<mailto:[email protected]>.
To view this discussion on the web visit
https://groups.google.com/d/msgid/hugin-ptx/c4cb55f9-c593-4582-b39b-134f10fb3f7an%40googlegroups.com
<https://groups.google.com/d/msgid/hugin-ptx/c4cb55f9-c593-4582-b39b-134f10fb3f7an%40googlegroups.com?utm_medium=email&utm_source=footer>.
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
--
A list of frequently asked questions is available at:
http://wiki.panotools.org/Hugin_FAQ <http://wiki.panotools.org/Hugin_FAQ>
---
You received this message because you are subscribed to the Google
Groups "hugin and other free panoramic software" group.
To unsubscribe from this group and stop receiving emails from it, send
an email to [email protected]
<mailto:[email protected]>.
To view this discussion on the web visit
https://groups.google.com/d/msgid/hugin-ptx/8EEB5682-393E-445B-A1E2-F6031DC3193B%40gmail.com
<https://groups.google.com/d/msgid/hugin-ptx/8EEB5682-393E-445B-A1E2-F6031DC3193B%40gmail.com?utm_medium=email&utm_source=footer>.
--
A list of frequently asked questions is available at:
http://wiki.panotools.org/Hugin_FAQ
---
You received this message because you are subscribed to the Google Groups "hugin and other free panoramic software" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/hugin-ptx/da3092be-e888-4f57-005f-82afb5106b92%40gmail.com.
