Since you didn’t share the actual errors I can’t really suggest anything...
Regards, John Ralls > On Jan 24, 2018, at 2:57 PM, R. Victor Klassen <rvklas...@gmail.com> wrote: > > This got me much further. > > The next problem was that no matter how many times I re-tried, gnutls would > not check out. I finally pulled it down by hand, extracted it to what > appears to be the right place, and then continued from the configure phase - > that seemed to work. The symptom was 30 minutes of waiting while 0 bytes > downloaded and then a timeout. [I must say I would not be patient for 30 > minutes of 0 bandwidth]. > > Continuing on, xmlsec failed to build. I think the errors were all in evp.c > > fatal error: too many errors emitted, stopping now [-ferror-limit=] > 1 warning and 20 errors generated. > make[3]: *** [libxmlsec1_openssl_la-evp.lo] Error 1 > make[2]: *** [all-recursive] Error 1 > make[1]: *** [all-recursive] Error 1 > make: *** [all] Error 2 > *** Error during phase build of xmlsec: ########## Error running make -j 5 > *** [45/72] > > For this one I have no idea what to try next. > > >> On Jan 21, 2018, at 12:36 PM, John Ralls <jra...@ceridwen.us >> <mailto:jra...@ceridwen.us>> wrote: >> >> >> >>> On Jan 19, 2018, at 1:46 PM, John Ralls <jra...@ceridwen.us >>> <mailto:jra...@ceridwen.us>> wrote: >>> >>> >>> >>>> On Jan 18, 2018, at 1:26 PM, R. Victor Klassen <rvklas...@gmail.com >>>> <mailto:rvklas...@gmail.com>> wrote: >>>> >>>> After a few years of being too busy to try working on the code base, I >>>> thought I’d make another attempt at installing a development version of >>>> GnuCash. Following the instructions on >>>> https://wiki.gnucash.org/wiki/MacOSX/Quartz >>>> <https://wiki.gnucash.org/wiki/MacOSX/Quartz> >>>> <https://wiki.gnucash.org/wiki/MacOSX/Quartz >>>> <https://wiki.gnucash.org/wiki/MacOSX/Quartz>>, I began by creating a new >>>> user, to be certain the environment wasn’t polluted by my previous attempt. >>>> >>>> I was successful in downloading gtk-osx-build-setup.sh >>>> >>>> I then ran it from the command line, and after a half-dozen or so tries, >>>> succeeded. (prior attempts hung at 9% or less complete - I presume this >>>> is temporary). >>>> >>>> There were three warnings: >>>> >>>> WARNING: aclocal not available (usually part of package 'autoconf') >>>> WARNING: automake not available (usually part of package 'automake') >>>> WARNING: yelp-tools not available (usually part of package 'yelp-tools') >>>> Configuring jhbuild without autotools >>>> >>>> Are these a problem? >>>> >>>> I then pulled down >>>> http://github.com/gnucash/gnucash-on-osx/raw/master/.jhbuildrc-custom >>>> <http://github.com/gnucash/gnucash-on-osx/raw/master/.jhbuildrc-custom> >>>> <http://github.com/gnucash/gnucash-on-osx/raw/master/.jhbuildrc-custom >>>> <http://github.com/gnucash/gnucash-on-osx/raw/master/.jhbuildrc-custom>> >>>> >>>> At this point I attempted to uncomment the line >>>> >>>> skip.remove( “bash” ) >>>> >>>> But it wasn’t in there. So I added it, and when I attempted to run >>>> jhbuild it complained. So I removed the line. Is this it no longer a >>>> relevant instruction? >>>> >>>> I then attempted to run >>>> >>>> jhbuild build openssl >>>> >>>> Which yielded the response: >>>> >>>> jhbuild build: failed to parse >>>> /Users/gnucashdev/Source/jhbuild/modulesets/http:/git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules: >>>> >>>> <http://git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules:> >>>> >>>> <http://git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules: >>>> >>>> <http://git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules:>> >>>> [Errno 2] No such file or directory: >>>> u'/Users/gnucashdev/Source/jhbuild/modulesets/http:/git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules' >>>> >>>> <http://git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules'> >>>> >>>> <http://git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules' >>>> >>>> <http://git.gnome.org/browse/gtk-osx/plain/modulesets-stable/gtk-osx.modules'>> >>>> >>>> At which point I am not sure how to proceed. In particular. I’m not even >>>> sure whether this should go to gnucash-devel or gtx-osx-devel >>> >>> The jhbuild warnings have to do with jhbuild bootstrapping itself. They're >>> normal. >>> >>> skip.remove("bash") isn't needed anymore, .jhbuildrc adds it only when the >>> MacOS version is < 10.11 (i.e. no SIP). >>> >>> I merged a PR the other day that updates openssl to 1.1g and that seems to >>> build OK inline so it's no longer necessary to build it separately before >>> everything else. >>> >>> All of that aside, something is whacked and I can reproduce the broken >>> moduleset path using an alternate user... but it works fine when I'm me and >>> everything else is the same. >>> >> >> I found what was whacked: There was an error in gtk-osx-python.modules and >> jhbuild has this weird fallback mechanism where instead of reporting an >> error it tries to load the same moduleset from the jhbuild source directory >> (~/Source/jhbuild/modulesets), first stripped to the "file part" which >> sort-of makes sense but then with the whole URI as a filename, which doesn't >> at all. That of course fails and it's the error that gets reported, which >> isn't very helpful. My primary user id had an old version of >> gtk-osx-python.modules in the jhbuild sources so the problem wouldn't >> reproduce until I re-ran gtk-osx-build-setup.sh, which replaced it with the >> one in git. >> >> Regards, >> John Ralls >> >> > _______________________________________________ gnucash-devel mailing list gnucash-devel@gnucash.org https://lists.gnucash.org/mailman/listinfo/gnucash-devel
