Geert, I can not get this to fail. The test is in the one time run conversion of stored account names to GUID's and this test adds the old token value to an existing one. I have replicated this section of tests so every run of travis runs the same test 6 times and still no failures. I have also added another test similar to the one that failed but again this does not fail.
At this time I am at a loss to why it fails, is there any thing else I can try ? Also I have been using these in travis.yml, just wondering if it is worthwhile adding something similar permanently... after_success: for file in $( find . -name 'test*.log' ); do echo -e "\n## $file"$'\n\n'"$(cat -- "$file")" >> all.txt; done && cat all.txt after_failure: for file in $( find . -name 'test*.log' ); do echo -e "\n## $file"$'\n\n'"$(cat -- "$file")" >> all.txt; done && cat all.txt Probably the success one is not required but the failure one or something similar would be. Bob On 21 February 2017 at 17:01, Geert Janssens <geert.gnuc...@kobaltwit.be> wrote: > Op maandag 13 februari 2017 10:52:27 CET schreef Robert Fewell: > > I added the following to travis.yml... > > > > after_failure: "cat src/engine/test/test-import-map.log" > > > > This forced a rerun of my copy, still no failure. > > > > Bob > > Bob, > > As travis started failing again today, I readded the after_failure clause > and > this time I managed to capture the output of test-import-map: > > cat src/engine/test/test-import-map.log > Running main() from gtest_main.cc > [==========] Running 7 tests from 3 test cases. > [----------] Global test environment set-up. > [----------] 1 test from ImapTest > [ RUN ] ImapTest.CreateImap > [ OK ] ImapTest.CreateImap (1 ms) > [----------] 1 test from ImapTest (1 ms total) > > [----------] 3 tests from ImapPlainTest > [ RUN ] ImapPlainTest.FindAccount > [ OK ] ImapPlainTest.FindAccount (0 ms) > [ RUN ] ImapPlainTest.AddAccount > [ OK ] ImapPlainTest.AddAccount (0 ms) > [ RUN ] ImapPlainTest.DeleteAccount > [ OK ] ImapPlainTest.DeleteAccount (0 ms) > [----------] 3 tests from ImapPlainTest (0 ms total) > > [----------] 3 tests from ImapBayesTest > [ RUN ] ImapBayesTest.FindAccountBayes > [ OK ] ImapBayesTest.FindAccountBayes (1 ms) > [ RUN ] ImapBayesTest.AddAccountBayes > > (process:18823): gnc.engine-CRITICAL **: gnc_account_imap_add_account_ > bayes: > assertion 'acc != NULL' failed > [ OK ] ImapBayesTest.AddAccountBayes (0 ms) > [ RUN ] ImapBayesTest.ConvertAccountBayes > gtest-import-map.cpp:381: Failure > Expected: 6 > To be equal to: value->get<int64_t>() > Which is: 1 > [ FAILED ] ImapBayesTest.ConvertAccountBayes (0 ms) > [----------] 3 tests from ImapBayesTest (1 ms total) > > [----------] Global test environment tear-down > [==========] 7 tests from 3 test cases ran. (2 ms total) > [ PASSED ] 6 tests. > [ FAILED ] 1 test, listed below: > [ FAILED ] ImapBayesTest.ConvertAccountBayes > > 1 FAILED TEST > > > Perhaps it can help you debug this issue. It think it deserves some more > attention because if there's a heisenbug in the bayes code that happens > (ir)regularly on travis it will no doubt also pop up in regular use later > on. > > Geert > _______________________________________________ gnucash-devel mailing list gnucash-devel@gnucash.org https://lists.gnucash.org/mailman/listinfo/gnucash-devel
