On Dec 11, 2011, at 2:47 PM, John Ralls wrote:
>
> On Dec 11, 2011, at 11:30 AM, David Reiser wrote:
>
>> On Dec 11, 2011, at 1:41 PM, John Ralls wrote:
>>
>>>
>>> On Dec 10, 2011, at 10:23 PM, David Reiser wrote:
>>>
>>>>
>>>> On Dec 11, 2011, at 12:39 AM, John Ralls wrote:
>>>>
>>>>>
>>>>> On Dec 10, 2011, at 8:03 PM, David Reiser wrote:
>>>>>
>>>>>> r21708 fixed my build problem (thanks John), but gnucash fails to launch
>>>>>> with:
>>>>>>
>>>>>> Backtrace:
>>>>>> In unknown file:
>>>>>> ?: 21* [#<procedure #f ()>]
>>>>>> ?: 22* (let* ((file #)) (cond (# => #) (# => #)))
>>>>>> ?: 23 [#<procedure #f #>
>>>>>> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>>>> ?: 24 [with-fluid* #<fluid 7> #f #<procedure #f ()>]
>>>>>> ?: 25* [#<procedure #f ()>]
>>>>>> ?: 26* [load-file #<primitive-procedure primitive-load> ...]
>>>>>> ?: 27* [save-module-excursion #<procedure #f ()>]
>>>>>> ?: 28 (let (# #) (dynamic-wind # thunk #))
>>>>>> ?: 29 [dynamic-wind #<procedure #f ()> #<procedure #f ()> #<procedure
>>>>>> #f ()>]
>>>>>> ?: 30* [#<procedure #f ()>]
>>>>>> ?: 31* [primitive-load
>>>>>> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>>>> In
>>>>>> /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>>>> 125: 32* [for-each #<procedure #f (x)> (trial-balance transaction
>>>>>> sx-summary ...)]
>>>>>> In unknown file:
>>>>>> ?: 33* [#<procedure #f (x)> balsheet-eg]
>>>>>> In
>>>>>> /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>>>> 127: 34* [module-use! #<directory (gnucash report standard-reports)
>>>>>> 109f68880> ...
>>>>>> 129: 35* [resolve-interface (gnucash report standard-reports
>>>>>> balsheet-eg)]
>>>>>> In unknown file:
>>>>>> ?: 36 (letrec ((get-keyword-arg #)) (let* (# # # ...) (and # #) ...))
>>>>>> ?: 37 (let* (# # # # ...) (and # #) (if # public-i #))
>>>>>> ?: 38* (and (or (not module) (not public-i)) (error "no code for module"
>>>>>> name))
>>>>>> ?: 39 [error "no code for module" (gnucash report standard-reports
>>>>>> balsheet-eg)]
>>>>>> ...
>>>>>> ?: 40 [scm-error misc-error #f ...]
>>>>>>
>>>>>> <unnamed port>: In procedure scm-error in expression (scm-error (quote
>>>>>> misc-error) #f ...):
>>>>>> <unnamed port>: no code for module (gnucash report standard-reports
>>>>>> balsheet-eg)
>>>>>>
>>>>>> This looks like it might be related to moving balsheet-eg in r21591.
>>>>>> Geert, could you take a look?
>>>>>>
>>>>>
>>>>> Try:
>>>>> make maintainer-clean
>>>>> find src -name gnucash -type d
>>>>> rm -rf everything you find *except* gnc-module/(foo|bar|baz)/gnucash
>>>>>
>>>>> Then autogen, configure, build, and install and try again.
>>>>>
>>>>> Regards,
>>>>> John Ralls
>>>>>
>>>> I didn't exactly follow part of that: the found files were:
>>>> src/gnc-module/test/mod-bar/gnucash
>>>> src/gnc-module/test/mod-baz/gnucash
>>>> src/gnc-module/test/mod-foo/gnucash
>>>>
>>>> Looking at the contents of one of those directories looked like it
>>>> wouldn't interfere on launch. If any of those should be removed, let me
>>>> know and I'll try again.
>>>>
>>>> But the source directory was a completely clean checkout from yesterday
>>>> afternoon, and the only config/build activity was the build failure fixed
>>>> in 21708.
>>>>
>>>> No change in result on launching gnucash. I do rm -rf base/install/dir
>>>> too, before installing the new version in an old location.
>>>
>>> David,
>>>
>>> Sorry, yes, those are the directories I meant.
>>>
>>> What about your installation directories? Might they still have old Scheme
>>> files or shared libraries?
>>>
>>> Try removing (rm -rf) lib/gnucash and share/gnucash, then re-running make
>>> install.
>>>
>>> I just tested r21710 and it started up OK -- but I did have to clean out
>>> the installation and reinstall for it to work.
>>>
>>> Regards,
>>> John Ralls
>>>
>> Still no joy for me. I almost always rm -rf $PREFIX/* before make install
>> (needed once in the deep dark past, so I got in the habit of doing it every
>> time). I also removed lib/gnucash and share/gnucash before reinstalling.
>>
>> My guile is not in a standard location, but that hasn't been a problem
>> before. I'm using guile 1.8.8 and swig 2.0.4
>
>
> OK, then it's not an installation problem; you must have obsolete code
> somewhere.
> (Yes, I know you said it was a clean checkout.)
>
> $ manjusri:svn/src/gnucash-git/src> grep -r "standard-reports balsheet-eg"
> --include="*.scm" .
> $ manjusri:svn/src/gnucash-git/src>
>
> What do you get?
>
> Regards,
> John Ralls
[14:57:03] dbr@DOPL6: gnucash $grep -r "standard-reports balsheet-eg"
--include="*.scm" .
[14:57:05] dbr@DOPL6: gnucash $
but I think that extra balsheet-eg is coming from the (list x) in
src/report/standard-reports/standard-reports.scm:
(for-each
(lambda (x)
(module-use!
(current-module)
(resolve-interface (append '(gnucash report
standard-reports) (list x)))))
(get-report-list))
Dave
--
David Reiser
dbrei...@earthlink.net
_______________________________________________
gnucash-devel mailing list
gnucash-devel@gnucash.org
https://lists.gnucash.org/mailman/listinfo/gnucash-devel
