I installed the following from PACKMAN in this order libktoblzcheck1-1.15-42.pm.1 ktoblzcheck-1.15-42.pm.1 libaqhbci10-2.3.2-0.pm.1 libaqbanking16-2.3.2-0.pm.1 aqbanking-qt3-2.3.2-0.pm.1 aqbanking-2.3.2-0.pm.1
then ./configure --enable-hbci this time I noticed that the ofx hbci option was listed after it finished make make install but still no setp hbci in the TOOLS menu. regards, John Rauch Christian wrote: > I have installed the following: > > ktoblzcheck-1.15-42.pm.1 > libktoblzcheck1-1.15-42.pm.1 > aqbanking-2.3.2-0.pm.1 > aqbanking-qt3-2.3.2-0.pm.1 > libaqbanking16-2.3.2-0.pm.1 > libaqhbci10-2.3.2-0.pm.1 > > and GnuCash 2.2.1 on x86_64 from [1] and I have hbci setup in Tools. > I don't know which aqbanking packages you installed, those from packman > or some others? > I did not try i586, but I suppose it works too. > > Regards, > Chris > > [1] > ftp://ftp.rauchs-home.de/suse/10.2/x86_64/gnucash-2.2.1-0.rauch.1.x86_64.rpm > > John Sved schrieb: >> Hi Chris, >> >> I used the openSuSE 10.2 disk via YAST to check and install where necessary: >> >> gtk2-devel >> guile >> guile-devel >> pkgconfig >> perl-XML-Parser >> perl >> libxml2-devel >> libgnomeui-devel >> libgnomeprint-devel >> libgnomeprintui-devel >> libglade2-devel >> gtkhtml2-devel >> doxygen >> opensp >> opensp-devel >> gwenhywfar-devel >> goffice-devel >> libtool >> >> From RPM pbone.net >> >> libktoblzcheck-devel >> >> Then from RPM pbone.net the following were downloaded. The order is >> as they were installed after an dependency warnings. (i.e. this will >> save others going back to to fetch yet another RPM ! note make sure >> that it is the right version for openSuSE or SuSE) >> >> libaqhbci10 2.3.2 >> libaqbanking16 2.3.2 >> libaqbanking-devel 2.3.2 >> libaqdtaus.so.3 >> libqbanking.so.4 >> libcbanking.so.16 >> aqbankinking-qt3 2.3.2 >> aqbanking 2.3.2 >> >> >> Then ./configure --enable-hbci >> make >> make install >> >> It worked ! but no setup HBCI in the tools menu :( >> >> So 3 hours of effort has not yet delivered the desired gnucash 2.2.1 >> with HBCI. >> >> Any suggestions ? >> >> regards >> John >> >> >> >> Rauch Christian wrote: >> >>> John Sved schrieb: >>> >>>> Hi, >>>> >>>> I am really just a user of gnucash. As I want to use the HBCI function >>>> which is not included in the binary RPM for openSuSE 10.2 I am >>>> reluctantly prepared to try to compile the source. >>>> >>> My Gnucash rpm is built against aqbanking, which provides HBCI. >>> You will have to install one of aqbanking-qt3 or aqbanking-gtk2 from >>> packman including their aqbanking to get the wizard in gnucash. >>> >>> >>>> The aqbanking 2.2.3 from distro RPM and libqwenhwfar 2.6.1 from >>>> downloaded RPM are installed >>>> >>> Use aqbanking 2.3.2 from packman (see above). >>> >>> >>>> So if someone would like to walk me through it, we may find the >>>> necessary pieces to actually compile gnucash 2.2.1 with HBCI on >>>> opensSuSE 10.2 for others to follow and avoid wasting a lot of time. >>>> >>> Complete build requirements for Gnucash on Suse 10.2 are as follows: >>> >>> aqbanking libaqbanking-devel gtk2-devel guile guile-devel pkgconfig >>> perl-XML-Parser perl libxml2-devel libgnomeui-devel libgnomeprint-devel >>> libgnomeprintui-devel libglade2-devel gtkhtml2-devel doxygen opensp >>> opensp-devel gwenhywfar-devel goffice-devel libtool libktoblzcheck-devel >>> >>> These may fetch some additional requirements I did not state explicitely. >>> >>> >>> >>>> Thanks, >>>> >>>> John >>>> >>> Regards, >>> Chris >>> >>> >>> > > _______________________________________________ gnucash-devel mailing list gnucash-devel@gnucash.org https://lists.gnucash.org/mailman/listinfo/gnucash-devel
