Dear Mark,
Once again I am very thankful to you for your reply, I
have extracted box vectors from .XTC file by using g_traj with -ob
option with this I was able to get only six vector components viz XX
YY ZZ YX ZX and ZY only how about remaining three vector components
XY XZ and YZ .
I have used triclinic box for my simulations I know that XY XZ and YZ
will be zero, moreover I have used " pcoupltype = anisotropic "
with compressibility values as "compressibility = 4.5e-5 4.5e-5
4.5e-5 0.0 0.0 0.0" in my .mdp file.
Here my question is why I am not getting XY XZ and YZ components in
my output file though they might be zero. Is this because of above
specified .mdp options or something else ?
Can you please let me know what might be the probable reason ?
Thank you in advance.
On Thu, Aug 16, 2012 at 11:17 AM, Mark Abraham <mark.abra...@anu.edu.au> wrote:
> On 16/08/2012 3:22 PM, ramesh cheerla wrote:
>>
>> Dear Mark,
>>
>> Thank you for your reply, as you suggested I will go
>> through the sec 7.4 and 8 of the manual and moreover how would I get
>> exact box vectors XX YY ZZ XY XZ YX YZ ZX ZY for each frame of
>> trajectory in gromacs
>
>
> They're in the trajectory file with each frame.
>
>
>> As I am new to gromacs I have no Idea where these will be stored (
>> other than gro file ). In NAMD .XTC file contains box vectors for
>> each step of the simulation like this is there any file in gromacs
>> that stores these box vectors for each step,
>
>
> Same.
>
>
>> if so how can i extract
>> them.
>
>
> Probably however you did so with NAMD, or with g_traj or gmxdump.
>
> Mark
>
>
>>
>> Please suggest me a way.
>>
>> Thank you.
>>
>> On Thu, Aug 16, 2012 at 4:52 AM, Mark Abraham <mark.abra...@anu.edu.au>
>> wrote:
>>>
>>> On 16/08/2012 5:46 AM, ramesh cheerla wrote:
>>>>
>>>> Dear Gromacs users,
>>>>
>>>> I am using gromacs for simulations of a polymer, for that I
>>>> am planing to see how lattice parameters a , b & c are varying
>>>> during simulation. Here lattice parameter "a" is the length of unit
>>>> cell along X- direction, "b" is the length of the unit cell along
>>>> "Y" axis and "c" is along Z -axis.
>>>> For my polymer polymer chains are not exactly oriented along Z-
>>>> direction they are a little bit tilted from the Z- axis. "a" and "b"
>>>> are along "x" and "Y" directions respectively so that I can get
>>>> lattice parameters "a" and "b" just by dividing box lengths along
>>>> those directions with the number of unit cells in those directions.
>>>> As the c- direction and Z- direction are not exactly same ( "c" is a
>>>> little bit tilted from Z ) in this case I shouldn't divide the box
>>>> length along Z - direction with the number of unit cells in that
>>>> direction to get lattice parameter "c". Here my questions are:
>>>> 1) How can I calculate exact "C" lattice parameter from simulation
>>>> data ? is there any way to get appropriate "c"?
>>>> 2) How one can get box vectors XX YY ZZ XY XZ YX YZ ZX and ZY for
>>>> total trajectory, as g_energy is giving only Box - X , Box-Y and Box-
>>>> Z but i need exact box vectors for valid lattice parameters
>>>> calculations.
>>>
>>>
>>> Sounds like g_energy is reminding you that you had a rectilinear
>>> simulation
>>> cell when you started, and still do. There are various ways to measure
>>> angles that will help you address your problem, if you check out manual
>>> sections 7.4 and 8.
>>>
>>> Mark
>>> --
>>> gmx-users mailing list gmx-users@gromacs.org
>>> http://lists.gromacs.org/mailman/listinfo/gmx-users
>>> * Only plain text messages are allowed!
>>> * Please search the archive at
>>> http://www.gromacs.org/Support/Mailing_Lists/Search before posting!
>>> * Please don't post (un)subscribe requests to the list. Use the www
>>> interface or send it to gmx-users-requ...@gromacs.org.
>>> * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
>
>
> --
> gmx-users mailing list gmx-users@gromacs.org
> http://lists.gromacs.org/mailman/listinfo/gmx-users
> * Only plain text messages are allowed!
> * Please search the archive at
> http://www.gromacs.org/Support/Mailing_Lists/Search before posting!
> * Please don't post (un)subscribe requests to the list. Use the www
> interface or send it to gmx-users-requ...@gromacs.org.
> * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
--
gmx-users mailing list gmx-users@gromacs.org
http://lists.gromacs.org/mailman/listinfo/gmx-users
* Only plain text messages are allowed!
* Please search the archive at
http://www.gromacs.org/Support/Mailing_Lists/Search before posting!
* Please don't post (un)subscribe requests to the list. Use the
www interface or send it to gmx-users-requ...@gromacs.org.
* Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
