Here's the video card as per "lspci -vv"
==========================================
02:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO]
(rev 01) (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc RV280 [Radeon 9200 PRO]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at cc00 [size=256]
Region 2: Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fde00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
==========================================
At bootup, I get the following (saved in dmesg)
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
and I get the following in the X log file. Can I ignore it?
(WW) RADEON(0): DRI init changed memory map, adjusting ...
(WW) RADEON(0): MC_FB_LOCATION was: 0xd7ffd000 is: 0xd7ffd000
(WW) RADEON(0): MC_AGP_LOCATION was: 0xffffffc0 is: 0xffffffc0
==========================================
==========================================
The following appears in the X log...
(II) LoadModule: "freetype"
(WW) Warning, couldn't open module freetype
(II) UnloadModule: "freetype"
(EE) Failed to load module "freetype" (module does not exist, 0)
==========================================
==========================================
Due to bad experiences with fglrx, I'm using the open source ATI
drivers. I get the following in the X log...
(EE) AIGLX error: dlopen of /usr/lib/dri/r200_dri.so failed
(/usr/lib/dri/r200_dri.so: cannot open shared object file: No such file or
directory)
(EE) AIGLX: reverting to software rendering
==========================================
==========================================
In xorg.conf, I've commented out all fontpaths except...
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/75dpi/"
...but the log still shows...
(WW) The directory "/usr/share/fonts/OTF" does not exist.
Entry deleted from font path.
(**) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/,
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/,
built-ins
==========================================
Any comments/suggestions?
--
Walter Dnes <waltd...@waltdnes.org>
