On 11/25/06, Stroller <[EMAIL PROTECTED]> wrote:
On 26 Nov 2006, at 02:01, Mark Knecht wrote:
> ...
> I do have the ath_pci driver and I can modprobe it successfully:
>
> Sector9 ~ # modprobe ath_pci
> Sector9 ~ # lsmod
> Module Size Used by
> <SNIP>
> ath_pci 72800 0
> ath_rate_sample 10880 1 ath_pci
> <SNIP>
> ath_hal 189264 3 ath_pci,ath_rate_sample
> <SNIP>Sector9 ~ #
>
> I don't see any errors in dmesg, or even any messages.
>
> Since I cannot get ndiswrapper working how would I go about getting
> ath_pci to work?
What card do you actually have? IMO NDISwrapper is a last resort for
cards that have no native support & for users who cannot afford a
supported card.
I completely agree.
You should certainly be using madwifi or madwifi-ng
(the driver which provides ath_pci, IIRC) if your card supports it.
What does `lspic -vt` say?
I assume you meant lspci:
Sector9 ~ # lspci -vt
-[0000:00]-+-00.0 nVidia Corporation C51 Host Bridge
+-00.1 nVidia Corporation C51 Memory Controller 0
+-00.2 nVidia Corporation C51 Memory Controller 1
+-00.3 nVidia Corporation C51 Memory Controller 5
+-00.4 nVidia Corporation C51 Memory Controller 4
+-00.5 nVidia Corporation C51 Host Bridge
+-00.6 nVidia Corporation C51 Memory Controller 3
+-00.7 nVidia Corporation C51 Memory Controller 2
+-02.0-[0000:01]--
+-04.0-[0000:02]--
+-05.0 nVidia Corporation C51 PCI Express Bridge
+-09.0 nVidia Corporation MCP51 Host Bridge
+-0a.0 nVidia Corporation MCP51 LPC Bridge
+-0a.1 nVidia Corporation MCP51 SMBus
+-0a.2 nVidia Corporation MCP51 Memory Controller 0
+-0b.0 nVidia Corporation MCP51 USB Controller
+-0b.1 nVidia Corporation MCP51 USB Controller
+-0d.0 nVidia Corporation MCP51 IDE
+-0e.0 nVidia Corporation MCP51 Serial ATA Controller
+-0f.0 nVidia Corporation MCP51 Serial ATA Controller
+-10.0-[0000:03]--+-08.0 Lite-On Communications Inc LNE100TX
| \-0a.0 Atheros Communications, Inc.
AR5005G 802.11abg NIC
+-10.1 nVidia Corporation MCP51 High Definition Audio
+-14.0 nVidia Corporation MCP51 Ethernet Controller
+-18.0 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
+-18.1 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
+-18.2 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller
\-18.3 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Sector9 ~ #
What does `iwconfig` say?
Actually, this is interesting and (so far) unexplained. I did not
intentionally ask the system to load ath_pci but it has done that. It
appears that ath_pci may have grabbed to hardware and hence stopped
ndiswrapper from using the card? No wonder I'm told that wlan0 doesn't
exist!
Sector9 ~ # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
wifi0 no wireless extensions.
ath0 IEEE 802.11b ESSID:""
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power:0 dBm Sensitivity=0/3
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/94 Signal level=-95 dBm Noise level=-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Sector9 ~ #
So, then I have two questions:
1) What is the proper way to configure this card using ath0, assuming
it actually is supported?
2) If the above data is about my card then why isn't is coming up
802.11g? I get .11g support from ndiswrapper, or did when it
worked...)
I do have madwifi installed but I'm not intentionally trying to run
it, as far as I know:
Sector9 ~ # eix -I madwifi
* net-wireless/madwifi-ng
Available versions: 0.0.1443.20060207 0.0.1531.20060427 0.9.2
Installed: 0.9.2
Homepage: http://www.madwifi.org/
Description: Next Generation driver for Atheros based
IEEE 802.11a/b/g wireless LAN cards
* net-wireless/madwifi-ng-tools
Available versions: 0.0.1443.20060207 0.0.1531.20060427 ~0.9.1
~0.9.2_rc1692 0.9.2
Installed: 0.9.2
Homepage: http://www.madwifi.org/
Description: Next Generation tools for configuration of
Atheros based IEEE 802.11a/b/g wireless LAN cards
Found 2 matches.
Sector9 ~ #
Sector9 ~ # rc-update show
alsasound | default
bootmisc | boot
checkfs | boot
checkroot | boot
clock | boot
consolefont | boot
cupsd | default
hostname | boot
hotplug | default
keymaps | boot
local | default nonetwork
localmount | boot
modules | boot
net.lo | boot
net.wlan0 | default
netmount | default
ntpd | default
rmnologin | boot
sshd | default
syslog-ng | default
urandom | boot
vixie-cron | default
xdm | default
Sector9 ~ # cat /etc/modules.autoload.d/kernel-2.6
# /etc/modules.autoload.d/kernel-2.6: kernel modules to load when system boots.
#
# Note that this file is for 2.6 kernels.
#
# Add the names of modules that you'd like to load when the system
# starts into this file, one per line. Comments begin with # and
# are ignored. Read man modules.autoload for additional details.
# For example:
# 3c59x
#forcedeth
ndiswrapper
agpgart
nvidia-agp
#tulip
Sector9 ~ #
Thanks,
Mark
--
gentoo-user@gentoo.org mailing list
